background image

16

foregoing shall constitute the sole remedy of the purchaser and the exclusive liability of
Cooper Wheelock, Inc.
In no case will Cooper Wheelock, Inc.'s liability exceed the purchase price paid for a
product.

 Limitation of Liability

Cooper Wheelock, Inc.'s liability on any claim of any kind, including negligence, breach
of warranty, or otherwise, for any loss or damage resulting from, arising out of, or
connected with any contract, or from the manufacture, sale, delivery, resale, repair or use
of any product shall be limited to the price applicable to the product or part thereof which
gives rise to the claim. Cooper Wheelock, Inc.'s liability on any claim of any kind shall
cease immediately upon the installation in the product of any part not furnished by
Cooper Wheelock, Inc. In no event shall Cooper Wheelock, Inc. be liable for any claim
of any kind unless it is proven that our product was a direct cause of such claim.
FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF
NEGLIGENCE, SHALL COOPER WHEELOCK, INC. BE LIABLE FOR
INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES.
  Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the preceding limitation may not apply to all purchasers.

Summary of Contents for SAFEPATH4 SP4-LOC

















Reviews: