background image

31

Appendix

1.1The unit can only be repaired by qualified installer centre personnel or an authorised 
     dealer.

for Europe market

1.2 This appliance is not intended for use by persons (including children) with reduced physical
      sensory or mental capabilities, or lack of experience and knowledge, unless they have been
      given supervision or instruction concerning use of the appliance by a person responsible for 
      their safety. 

for Europe market

      Children should be supervised to ensure that they do not play with the appliance.
1.3 Please make sure that the unit and power connection have good earthing, otherwise may 
      cause electrical shock.
1.4 If the supply cord is damaged, it must be replaced by the manufacturer or our service agent
      or similarly qualified person in order to avoid a hazard.
1.5 Directive 2002/96/EC (WEEE): 
      The symbol depicting a crossed-out waste bin that is underneath the appliance indicates 
       that this product, at the end of its useful life, must be handled separately from domestic
       waste, must be taken to a recycling centre for electric and electronic devices or handed 
       back to the dealer when purchasing an equivalent appliance. 
1.6 Directive 2002/95/EC (RoHs): This product is compliant with directive 2002/95/EC (RoHs) 
      concerning restrictions for the use of harmful substances in electric and electronic devices.
1.7 The unit CANNOT be installed near the flammable gas. Once there is any leakage of the gas
     , fire can be occur.
1.8 Make sure that there is circuit breaker for the unit, lack of circuit breaker  can lead to 
      electrical shock or fire.
1.9 The heat pump located inside the unit is equipped with an over-load protection system. It 
      does not allow for the unit to start for at least 3 minutes from a previous stoppage.
1.10 The unit can only be repaired by the qualified personnel of an installer center or an 
         authorized dealer. 

for North America market

1.12 Installation must be performed in accordance with the NEC/CEC by authorized person only.
       

for North America market

1.13 USE SUPPLY WIRES SUITABLE FOR 75

.

1.14 Caution: Single wall heat exchanger, not suitable for potable water connection.

8.1.Caution & Warning

Summary of Contents for CH-HP07MNK




































Reviews: