manualshive.com logo in svg

Coolmay CX-WIFI-2NET, User Manual

Share
Download
Coolmay CX-WIFI-2NET User Manual Download Page 1

                                                       

CX-WIFI-2NET module user manual           

      

 

Shenzhen Coolmay Technology Co.,Ltd                                                                                                       

www.coolmay.com

 

Page 

1

 ,Total 93 Pages 

 
 

CX-WIFI-2NET Module user 

manual 

 
 
 

Shenzhen  Coolmay  Technology  Co.,Ltd

   

Version  7.21 

 

 

 
 
 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
CX-WIFI-2NET module is an all-in-one 802.11 b/g/n Wi-Fi and Ethernet module that 
provides a way to connect a user's physical device to a Wi-Fi wireless network or 
Ethernet. Provides a solution for the UART data transfer interface. The module comes 
with an RS485 port, a standard RS232 communication port and two RJ45 standard 
network ports. Through this module, the traditional low-end serial device or 
MCU-controlled device can easily access Wi-Fi wireless network or Ethernet. 
Transparent transmission is realized to realize the control and management of the 
Internet of Things. 
As a hotspot, CX-WIFI-2NET module can accommodate 32 wifi clients simultaneously, 

Summary of Contents for CX-WIFI-2NET






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands