5
ENGLISH
•
Unscrew the clamp (13) and extend the bar (12) to the
desired height and fix it by tightening the clamp (13) with
a slight effort as you turn it clockwise.
•
Install the motor unit (9) on the telescopic bar (12)
until bumping and fix it with the clamp (11) turning it
clockwise.
•
Unscrew and remove the rear grid (7) fastening nut (4).
•
Install the rear grid (7) on the motor unit (9). The car-
rying handle (5) on the rear grid (7) should be turned
upwards.
•
Fix the rear grid (7) on the motor unit (9) with the nut (4)
by screwing it clockwise until bumping.
•
Install the blades (3) on the motor axis (6) and fix them
with the clamp (2), rotating it counterclockwise, hold-
ing the blades (3) with a free hand.
•
Open the clamps on the rear grid (7).
•
Match the front (1) and the rear (7) protective grids and
close the clamps.
•
The fan is ready for operation.
USING THE REMOTE CONTROL (27)
ATTENTION!
The unit contains a lithium battery. Prevent children from
swallowing the lithium battery.
If your child has swal-
lowed a battery, immediately see your doctor.
Battery leakage can cause injuries or damage the
unit. To avoid the unit damage, follow the instructions
given below:
–
use only the «CR2025» battery;
–
do not recharge the battery;
–
insert the battery strictly following the polarity;
–
remove the battery if you are not planning to use the
unit for a long time;
–
replace the battery in time;
–
apply to specialized centers for further recycling of the
battery;
–
avoid the power nippers circuit.
•
Remove the battery holder by pressing the side clamp,
install a CR2025 battery, strictly following the polarity.
•
Install the battery holder back to its place.
Note:
- if there is an isolation insert, remove the insert.
USAGE
•
Before using the unit for the first time, make sure
that the voltage in your mains corresponds to the unit
operating voltage.
•
Insert the plug into the mains socket, you will hear
a sound signal and the indicator (26) «POWER» will
light up.
•
Press the on/off button (19) «ON/OFF» or the on/
off button (19) «POWER» on the RC (27). The fan will
switch on at the low speed, and the indicator (23) «L»
will light up.
•
Press the button (19) «ON/OFF» or the button (21)
«POWER» on the RC (27) to select the blades rota-
tion speed:
«L» – low air flow speed;
«M» – medium air flow speed;
«H» – high air flow speed.
•
Press the button (8) to switch the 90° oscillation oper-
ating mode of the fan on.
•
Lift the button (8) to stop the fan oscillation mode.
•
Press the button (20) «TIMER» or the button (20)
«TIMER» on the RC (27) to select the timer operation
time, the indicators (24) will be glowing.
•
You can set the fan operation time from 0.5 hours to
7.5 hours «0,5Н-1Н-2Н-4Н» (with 0.5 hours setting
step).
•
The set timer operation time is shown with the indica-
tors (24).
•
To switch the timer off repeatedly press the button
«TIMER» or the button (20) «TIMER» on the RC (27) until
the indicators (24) go out.
•
To activate the air flow selection mode, press the
«MODE» button (22) on the remote control (27), the fan
will turn on in «NA» mode. To select the air flow mode
consecutively press the button (22) on the remote con-
trol (27).
•
The indicator lights (25) will show when the air flow
mode is selected:
«NA» – natural wind;
«SL» – moderating wind.
•
«Simple ventilation» mode is not shown with indicators.
•
To turn the air flow selection operation mode off, con-
secutively press the «MODE» button (22) on the remote
control (27), the indicator (25) will go out.
•
To switch the fan off, press the button (19) «ON/OFF» or
the button (19) «POWER» on the RC (27).
•
You may change the position of the motor unit (9) of the
fan in accordance with the required air flow angle in the
vertical position, the fan slope angle is set manually. To
change the fan slope angle press with a slight effort on
the motor unit (9) upwards or downwards. Clicking while
the fan is being tilted is normal.
MAINTENANCE AND CARE
•
Before cleaning the fan switch it off by pressing the but-
ton (19) «ON/OFF» or the button (19) «POWER» on the
remote control (27) and unplug it.
•
Do not use abrasive cleaners and solvents to clean
the unit.
•
Clean the motor unit (9) with a slightly damp cloth and
then wipe it dry.
•
If it is necessary to clean the blades (3), remove the
front grid (1) by repeating the steps of «Assembling the
fan» clause in reverse, and then wipe the blades (3) with
a slightly damp cloth.
•
Open the clamps on the rear grid (7).
•
Install the front grid (1) on the rear grid (7) and close
the clamps.
•
You may clean the fan blades with a vacuum cleaner
using a proper attachment.
•
Do not immerse the motor unit (9) of the fan into water
or any other liquids. Make sure that no liquids get into
the motor unit (9) of the fan to avoid its damage and
prevent risk of electric shock.
STORAGE
•
Unplug the fan and clean it.
•
If necessary, disassemble the fan.
•
Remove the front grid (1), unscrew the blade lock (2) by
turning it clockwise, remove the blades (3), unscrew
the fixing nut of the rear grid (4) and remove the grid (7).
•
Unscrew the clamp (11) and remove the motor unit (9)
from the telescopic bar (12).
•
Unscrew the clamp (17) and remove the telescopic bar
(14) from the base (15).
•
Pack the fan into the original package and put it away
for storage in a dry cool place away from children and
disabled persons.
