background image

NOTE: For proper operation, an independent dedicated circuit should be used for
each unit installed. Each circuit should be protected with a 20 amp circuit breaker.

When your application requires a high intense heat or you want a quick temperature
increase, the Power Cook mode should be used.

What to Do:

1. Turn the Cooktop “ON” by turning the control knob to the right.
2. Momentarily depress the Power Cook button.
3. Turn the control knob until the desired Power Cook setting (1-20) appears on the

LED Display.

4. Turn the control knob to the left to decrease power and to the right to increase

power.

5. To turn the Cooktop off, turn the control knob to the far left until it “clicks” and

the LED display no longer illuminates.

IMPORTANT:

You can switch between SmarTemp and Power Cook at anytime just

by pressing the SmarTemp/Power Cook button.

IMPORTANT INFORMATION

• Never heat an empty pan, it may damage the Cooktop or cookware and over-

heat the unit. When overheating occurs, an error code will flash on the LED
display and the Cooktop will shut itself off automatically. When the tempera-
ture returns to normal, the Cooktop will start to cook again.

• Remember to turn the Cooktop off after each use. 
• Keep the Cooktop away from gas and electric ranges or open flames. Do not

place in the oven. If the surrounding air temperature is too high, the Cooktop
will cease to function properly.

• Be sure to dry off the outside of the pan before use. Otherwise As If the pan

temperature rises, the water droplets on the outside of the pan may begin to
boil and spatter.

• Do not touch the ceramic plate (or the top of the Cooktop) immediately after

use. The heat from the pan will be transferred to the ceramic plate causing it to
be hot to the touch.

• Do not place any articles on the Cooktop other than inductive cookware. For

example, do not place cans on top of the Cooktop as they may explode.

• Do not use aluminum foil on top of the Cooktop.
• Do not use the Cooktop near a faucet, swimming pool, sink, or other areas

where water can be found. Never store the Cooktop outside or upside down.

• Do not obstruct, block, or alter the air entrance or outlet. Do not stick foreign

objects into these openings.

• Do not strike or damage the Cooktop. Do not put the Cooktop in your luggage.

Throwing or dropping the Cooktop can damage the internal components or
crack the Cooktop, voiding your Warranty. If the Cooktop becomes cracked,
unplug immediately and do not use.

3

Summary of Contents for MagnaWave MC1500












Reviews: