background image

PREPARING YOUR COOKTEK MAGNAWAVE COOKTOP FOR USE

Before operating your Cooktop, do the following:
1. Remove all packing material.
2. Place the unit on a dry, level, hard, stable, and non-flammable surface.
3. Keep unit away from other heat sources and allow at least 2 inches clearance for

air circulation at sides, front and rear of the unit. If either the air intake or
exhaust outlet is blocked, the internal temperature will rise, causing an error code
to occur.

Grounding Instructions:

The Cooktop must be properly grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing a safe path for the electric
current. The Cooktop has a power cord with a 3-prong grounding plug, which must
be used in a compatible and properly grounded outlet. It is the owner’s responsi-
bility to replace any 2-prong wall outlet with a properly grounded 3-prong wall
receptacle. 

For your safety, never cut, remove, or disable the electrical (ground) connection
from the plug. Never use an adapter plug or an extension cord with the Cooktop.

WARNING:

Electric shock can result from an improperly grounded plug. Please

consult a qualified electrician if you have any questions about these grounding
instructions.

Before You Begin:

Some units may come equipped with a removable IEC Power Cord.  Please make
sure that this power cord is firmly attached to your CookTek unit BEFORE plugging
the unit into the power receptacle and before attempting operation.

ELECTRICAL INSTALLATION REQUIREMENTS*

Every installation site has different electrical wiring. Because many different local
codes exist, it is the Owner and Installer’s responsibility to comply with those codes.
CookTek is not responsible for any consequential damages as a result of failure to
comply with installation requirements.

• Read all installation instructions carefully before starting installation.
• Remove Cooktop carefully from carton. 
• Remove all loose packaging and accessories. 
• It is the responsibility of the installer to comply with all federal, state and local

codes.

• Any installation not matching the specifications discussed in this manual auto-

matically voids the product’s warranty.

• CookTek recommends that a dedicated electrical line be used for each Cooktop

installed. Electrical circuits should not be shared with any other electrical
equipment.

1

Summary of Contents for MagnaWave MC1500












Reviews: