manualshive.com logo in svg

Cookology GGH301BK, User Manual, Page: 20 / 23

Share
Download
Cookology GGH301BK User Manual Download Page 20

20

o

Reassemble all the burners carefully; in particular you should
make sure that the flame spreader is correctly placed on the
burner.

o

IMPORTANT: The minimum flow adjustment process must be
completed before the appliance is next used.

Minimum flow adjustment for hob gas taps 

All work must be carried out by a GASSAFE 
registered engineer. 

IMPORTANT: Always isolate the hob from the electricity 
supply before changing the injectors and/or adjusting the 
minimum flow of the burners. 

o

Remove all the pan supports

、

caps

、

flame spreaders and

knobs.

o

Unscrew the screws of the
panel, then remove the panel.

o

Install cap

、

flame spreader

、

knob of the burner. Switch the
burner on and set the knob at
the minimum position.

GENERAL INJECTORS TABLE 

Power (in watts) 

Kind of gas  Nozzle 

mm/100 

Burners 

Max. Min. 

Natural 

    131

129 

97 
76 

Wok  

Rapid 

Semi-rapid 

Auxiliary 

1700 
1500 

900 
500 

L.P.G. 
Butane 
Propane 

     94

87 
65 
51 

Wok  

Rapid 

Semi-rapid 

Auxiliary 

3500 
3000 
1750 
1000 
3500 
3000 
1750 
1000 

1300 

700 
400 
350 

Summary of Contents for GGH301BK
























Reviews:

No comments