Contura C i10 Installation Instructions Manual Download Page 3

GB

19

NOTE!

Report installation of a stove to your local 
authority. 

The owner of the house is personally responsible 
for ensuring compliance with the mandatory safety 
requirements and must have the installation approved by 
a qualified inspector. Your local chimney sweep must also 
be informed about the installation as this will affect the 
routines for regular chimney-sweeping services.

Table of contents 

General 20
Important dimensions 

21

Prior to installation 

22

Installation 26
Connection to chimney 

27

Recessing the insert 

29

WARNING! 

During operation some of the surfaces of the inserts 
become extremely hot and can cause burn injuries if 
touched. Be aware of the strong heat radiated through 
the hatch glass. Placing flammable material closer than 
the safe distance indicated may cause a fire. Pyre lighting 
can cause quick gas ignition with the risk of damage to 
property and personal injury. 

A warm welcome to Contura.

A warm welcome to the Contura family. We hope you 
will get a great deal of pleasure from your new stove. 
As a new owner of a Contura stove, you have secured 
a product with timeless design and long service life. 
Contura also has a combustion process that is both 
environmentally friendly and efficient, for the best heat 
production.

Read through these installation instructions carefully 
before installation. Read how to best light your stove in 
the lighting instructions.

CONTENTS

Summary of Contents for C i10

















Reviews: