Contractors Wardrobe 6000H-180 Installation Instructions Manual Download Page 7

7

      I06000H-180-0704

Thank  you  for  purchasing  a  CW

®

  Shower Enclosure. 

This  is  only  one  of  a  large  line  of  shower  enclosures 

and  high  quality  wardrobe  door  products.  If  you  like 

this  product,  please  contact  Contractors  Wardrobe

®

 

for  more  information  about  our  many  beautiful

wardrobe doors in bi-pass and bi-fold styles with steel,

aluminum and hardwood frames.

CAUTION:  Since  the  Drip  Rail  (#11)  will  be  very  hard  to 

remove once in place, test fit and mark the Drip Rail (#11) 

location  before  removing  the  protective  paper  from  the 

two-way  adhesive.    Be  sure  the  Bottom  Rail  (#8)  is  clean 

and  free  of  oil  or  other  contaminants  before  attaching  the 

Drip Rail (#11) to it.

2. Install the assembled Drip Rail (#11) at a slope to allow 

water drainage to flow into the shower pan (See Figure 19). 

The Drip Rail (#11) should be installed 1/2

 from the edge 

of the Strike Rail (#7).

STEP 12  Cleaning the Enclosure

Clean  the  glass  and  enclosure  hardware  with  a  mild  non-

abrasive  cleaner  designed  for  glass  such  as  CW

®

  Mirror 

&  Glass  Cleaner.  Avoid  using  scouring  cleansers  as  this 

will  scratch  and  mar  the  beautiful  finish  on  the  enclosure.

Figure 18

Figure 19

Summary of Contents for 6000H-180








Reviews: