In this instruction booklet we will walk you through the
installation of your new shower door.
DO NOT REMOVE your existing shower door until you
check your new shower door kit for all the proper parts.
Make sure that you have all the proper tools required to
assemble your new shower door. Use the check list below.
Use a level to check that the sill/shower dam is reasonably
level - not more than 1/4
″
out of level from side to side.
Check the walls for levelness - not more than 1/4
″
out of
level from top to bottom. If it is out of level more than that,
you may need to order custom wall jambs.
Tools you will need:
Phillips Screwdriver
Level
Electric Drill
1/8
″
Drill Bit (for fiberglass stall)
3/16
″
Masonry Drill Bit (for tile stall)
7/64
″
Drill Bit
Fine File
Miter Box and Hacksaw with 32 Teeth/Inch Blade
Pliers
Pencil
Hammer
Caulking Gun - Tube of Clear Tub/Tile Silicone
Tape Measure
Safety Glasses
Scissors
CAUTION: Wear safety glasses whenever drilling or cutting.
Handle the Door Panel carefully. The corners of the panel
can damage tile and floor coverings. Tempered glass
cannot be cut.
STEP 1 Checking Contents Of
Shower Door Package
DO NOT use a razor blade to cut open the paper wrapping
as you may scratch the contents. Use the IPB Drawing to
help you locate the following parts:
Parts Check List:
No.
Qty.
Description
(#1)
1
Header - #6000
(#2)
1
Bottom Curb/Sill - #6000
(#3)
1
Insert Jamb - #6000
(#4)
1
Framed Door with
CW
®
Rotary Gear
Assembly with Magnetic Seal
(#5)
1
Slip Jamb Male - #6000
(#6)
1
Wall Jamb - #6000
(#9)
1
Outside Handle
(#10)
1
Inside Handle (with Holes)
(#11)
1
Drip Rail - #6000
(#12)
1
Drip Rail Gasket - #6000
(#13)
1
Magnetic Jamb Seal
(#14)
2
Snap-In Pivot Strip - #6000
(#15)
2
Sill Spacer (Clear)
(#16)
2
Setting Block
(#17)
1
Horizontal Press-In Vinyl
(#18)
1
Vertical Press-In Vinyl
(#20)
6
#8 x 1-1/2
″
PH SMS Screw
(#21)
6
Screw Anchor
(#22)
7
#6 x 1/4
″
“B”-Point Screw
(#23)
4
#6 x 7/16
″
“B”-Point Screw
(#24)
2
#8 x 1-1/2
″
FH SMS Screw
(#25)
1
In-Line Glass Panel
If you find that any parts are damaged or missing,
refer to the parts list and IPB Drawing and contact
Contractors Wardrobe
®
’s Customer Service Department
at 661-257-1177. NOTE: Views and directions given in
these instructions — left, right, front, back, etc. — are
from outside of the enclosure, facing the shower.
STEP 2 Removing the Existing Enclosure
(If this is a new installation, skip to Step 3)
After determining that your newly purchased enclosure kit
is the correct size, remove the existing shower door and
all existing parts of that door assembly. Remove all screw
anchors from the wall. Clean silicone sealant or shower
caulking and any other contaminants from shower and wall
surfaces.
STEP 3 Installing the Bottom Curb/Sill
and Wall Jamb
1. Using the Tape Measure, find the center of the shower
dam. Make a mark where the center is at both ends of the
dam (See Figure 1).
2. Cut the Sill Spacer (#15) to In-Line Glass Panel (#25)
width minus 1-1/2
″
. Cut another piece this size for the
Header (#1). Place the Sill Spacer (#15) into the groove of
the Bottom Curb/Sill (#2) (See Figure 2).
Figure 2
3
I06000H-180-0704
Figure 1
