Continental Fireplaces BCNV36N Installation And Operating Instructions Manual Download Page 4

4

W415-0861 / A / 02.10.11

2.0 INTRODUCTION

3.16B

!

WARNING

• 

THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• 

ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR IT’S CONTROLS CAN BE 
DANGEROUS AND IS PROHIBITED.

• 

Do not operate appliance before reading and understanding operating instructions. Failure to operate 
appliance according to operating instructions could cause fi re or injury.

• Risk 

of 

fi re or asphyxiation do not operate appliance with fi xed glass removed.

• 

Do not connect 110 volts to the control valve.

• 

Risk of burns. The appliance should be turned off and cooled before servicing.

• 

Do not install damaged, incomplete or substitute components.

• 

Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal 
edges may be sharp.

• 

Do not burn wood or other materials in this appliance.

• 

Children and adults should be alerted to the hazards of high surface temperature and should stay away 
to avoid burns or clothing ignition.  Toddlers, young children and others may be susceptible to accidental 
contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict 
access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and 
other at risk individuals out of the room and away from hot surfaces.

• 

Clothing or other fl ammable material should not be placed on or near the appliance.

• 

Due to high temperatures, the appliance should be located out of traffi c and away from furniture and 
draperies.

• 

Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot 
surfaces.

• 

Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• 

Check with your local hearth specialty dealer for safety screens and hearth guards to protect children 
from hot surfaces. These screens and guards must be fastened to the fl oor.

• 

Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• 

This appliance is a vented gas-fi red appliance.  Do not burn wood or other materials in this appliance.

• 

It is imperative that the control compartments, burners and circulating blower and its passageway in the 
appliance and venting system are kept clean. The appliance and its venting system should be inspected 
before use and at least annually by a qualifi ed service person. More frequent cleaning may be required 
due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and 
free from combustible materials, gasoline and other fl ammable vapors and liquids.

• 

Under no circumstances should this appliance be modifi ed.

• 

This appliance must not be connected to a chimney fl ue pipe serving a separate solid fuel burning 
appliance.

• 

Do not use this appliance if any part has been under water. Immediately call a qualifi ed service 
technician to inspect the appliance and to replace any part of the control system and any gas control 
which has been under water.

• 

Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass 
should be done by a licensed or qualifi ed service person.

• 

Do not strike or slam shut the appliance glass door.

• 

Only doors / optional fronts certifi ed with the unit are to be installed on the appliance.

• 

Keep the packaging material out of reach of children and dispose of the material in a safe manner. As 
with all plastic bags, these are not toys and should be kept away from children and infants.

• 

As with any combustion appliance, we recommend having your appliance regularly inspected and 
serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and 
your family against Carbon Monoxide.

• 

Ensure clearances to combustibles are maintained when building a mantel or shelves above the 
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, 
discolouration or damage to decorations, a T.V. or other electronic components.

Summary of Contents for BCNV36N

































Reviews: