irLEDFLAT QC -
5 RGBW LEDs compact projector with infrared remote control
Page 15
English
7 - Infrared remote control
The infrared remote control supplied with the projectors allows you to remotely access all the functions of the
projectors. The infrared sensor is located on the front of the projector.
Note : The remote control can also be used when the projector is in DMX mode.
1 - Black out button:
Turns the projectors ON or OFF.
2 - SELECT PROG button
: Launches built-in programs or allows you to choose colours. 4 different modes are
available, each pressure allows you to switch from one mode to another.
Note : Colours and programs available with the SELECT PROG button depends on the DMX mode currently
used:
Pure RGB or RGBW. Colours and programs are different for each DMX mode. Please refer to pages 6 to 14 for
more details about DMX modes.
You will need to select a DMX mode before using the SELECT PROG button.
1
st
pres-
sure
Red LEDs flashing
: Fixed colours, step and crossfade programs selection with the 1 to 9 buttons, and with
the + and - buttons.
Use the FLASH button and the
+
and
-
buttons to configure the strobe speed.
Use the FLASH button and the
+
and
-
buttons to configure the programs speed.
2
nd
pressure
Blue LEDs flashing
: Automatic mode.
Use the FLASH button and the
+
and
-
buttons to configure the strobe speed.
Use the FLASH button and the
+
and
-
buttons to configure the programs speed.
3 - FLASH button
: Activates or deactivates the Flash mode. Increase or decrease the flash speed with the + and -
buttons of the remote control. This button can be used with each mode described above.
4 - SPEED button
: Allows you to configure the the Step and Crossfade programs speed.
Increase or decrease the
speed with the + and - buttons of the remote control.
6 - DMX mode selection - DMX MODE buton
There are 13 different DMX modes.
You will need to select a DMX mode before controlling your projector in DMX mode ;
Press the DMX MODE and use the + and - buttons to switch from one mode to another :
LEDs ON
Mode
LED ON
Mode
Red
1CH2
Green and blue
2CH5
Green
1CH3
Green and White
2CH6
Blue
1CH4
Blue and White
2CH7
White
1CH5
Red, Green and Blue
3CH5
Red and Green
1CH6
Red, Green and White
3CH6
Red and Blue
2CH2
Red, Blue and White
3CH7
Red and white
2CH4
7 - SL/SA button
: Activates the music-sensitive (SA) or slave (SL) modes. When using the music-sensitive mode
(green LEDs), use the
+
and
-
to configure the microphone sensitivity. The slave mode is indicated by red LEDs.
8 - SET ADDR buttons and 0, 1, 2, 3, 4, 5, 6, 7, 8 and 9: Allows you to configure your projectors DMX address.
For instance, if you want to configure the address 245 :
- Press S, all the LEDs are flashing to indicate the beginning of the process.
- Press 2, the green LEDs of your projectors lit up to indicate the hundreds digit has been saved.
- Press 4, the blue LEDs of your projector lit up to indicate the tenths digit has been saved.
- Then press 5. All the LEDs will flash to confirm you the address has been saved properly.
Note
: If you want to use the address 5, you will need to enter 005.
9 - R, G, B and W buttons
:
Adjusts colours brightness,
R
for red,
G
for green,
B
for blue, and
W
for white.
Increase or decrease their brightness with the + and - buttons
.
The
A
(amber) button is not available for these projectors.
