Ver.1.05
AIO-163202FX-USB
6
Analog Output Connection (Shielded Cable)
-
If this product or the connected wire receives noise, or the distance between this product and the target is
long, data may not be outputted properly.
-
For analog output signal, the current capacity is ±5mA (Max.). Check the specification of the connected
device before connecting this product.
-
Do not short the analog output signal to analog ground, digital ground, and/or power line. Doing so may
damage this product.
-
Do not connect an analog output signal to any other analog output, either on this product or on an external
device, as this may cause a fault on this product.
-
Analog output signal outputs hundreds of
voltages when USB cable is inserted.
Digital I/O signals, Counter signals and Control
signals Connection
The following sections show examples of how to connect digital I/O
signals, counter I/O signals, and other control I/O signals (external
trigger input signals, sampling clock input signals, etc.). All the digital I/O
signals and control signals are LVTTL level signals.
Digital Input Connection
Digital Output Connection
About the counter input control signal
Counter Gate Control Input (refer to the chapter 3 Connector Pin
Assignment) acts as an input that validate or invalidate the input of an
external clock for the counter. This function enables the control of an
external clock input for the counter. The external clock for the counter
is effective when input is "High", and invalid when input is "Low". If
unconnected, it is a pull-up in this product and remains "High".
Therefore the external clock for the counter is effective when the
counter gate control input is not connected.
-
Do not short the output signals to analog ground, digital ground, and/or power line. Doing so may
damage the product.
-
If connected to each output, a pull-up resistor must be about 10k
to pull up with a 3.3V power source.
-
Each input accepts 5V TTL signals.
Difference from AIO-163202F-PE, ADA16-32/2(PCI)F and ADA16-32/2(CB)F
Item
AIO-163202FX-USB
AIO-163202F-PE
ADA16-32/2(CB)F
ADA16-32/2(PCI)F
Analog input
Buffer memory
128K data FIFO or 128K data RING
64K data FIFO or 64K data RING
External start signal,
External stop signal,
External clock signal
LVTTL level
TTL level
External status output signal
LVTTL level
TTL level
Analog output
Buffer memory
128K data FIFO or 128K data RING
64K data FIFO or 64K data RING
External start signal,
External stop signal,
External clock signal
LVTTL level
TTL level
External status output signal
LVTTL level
TTL level
Digital I/O
Number of input channels
Non-isolated input 8 channels (LVTTL level positive logic)
Non-isolated input 4 channels (LVTTL level
positive logic)
Non-isolated input 8 channels (TTL level positive
logic)
Number of output channels
Non-isolated output 8 channels (LVTTL level positive logic)
Non-isolated output 4 channels (LVTTL level
positive logic)
Non-isolated output 8 channels (TTL level positive
logic)
Counter
Number of channels
2 channels
1 channel
2 channels
Number of external inputs
LVTTL level
TTL level
Number of external outputs
LVTTL level
TTL level
Bus master transfer function
None
Have
Sync signal control connectors None
Have
None
Connector
96-pin half pitch connector [M (male) type]
68-pin 0.8mm-pitch connector [F (female) type]
*1
96-pin half pitch connector [M(male) type]
Power consumption (Max.)
5VDC 1300mA
3.3VDC 500mA, 12VDC 300mA
3.3VDC 600mA
5VDC 1100mA
Bus specification
USB Specification 2.0/1.1 standard
PCI Express Base Specification Rev. 1.0a x1
PC Card Standard Card Bus
PCI(32bit, 33MHz, Universal key shapes
supported )
Physical dimensions (mm)
180(L) x 140(D) x 34(H) (No protrusions)
169.33(L) x 110.18(H)
85.6(W) x 54.0(D) x 5.0(H) TYPE II
176.41(L) x 105.68(H)
Weight
400g
140g
80g
130g
*1: When you use the optional connector conversion cable ADC-68M/96F, connector is 96-pin half pitch connector [M (male) type].
CAUTION
CAUTION
PLUG-IN Electronic GmbH • Am Sonnenlicht 5 • 82239 Alling • Tel.: +49 (0) 8141 3697-0 • [email protected] • www.plug-in.de
