Operating elements
1
5
2
3
1 Dual-USB port (plug)
2 Car on-board power plug
3 LED indicator light
4 Retaining clip, at the back
5 Four-fold USB port
4
Operation
Always switch off the USB device to be connected before connecting it to a USB port. Make sure
the connection is correct. If the product is not connected properly, it could overheat or cause an
electric shock or fire.
Make sure, that your USB device is suitable for the connection values of the USB car charger.
Observe the information in chapter “Technical data”.
It is recommended to connect devices with high current consumption to the four-fold USB port,
because this is protected against overloading and is short circuit proof. Therefore only consumers
with low current consumption (below 1.5 A) should be connected to the dual-USB port (plug).
• Connect a switched off consumer to a USB port (1, 5) of the charger. If required, the four-fold USB port (5)
can be fixed at a suitable place in the vehicle, e.g. to a storage compartment on the seat or door, with the
retaining clip (3).
• Plug the car on-board power plug (2) into a car on-board power outlet in your vehicle. The LED indicator
lamp (3) lights up and indicates, that the product is ready for operation.
• The connected consumer is charged. If you want to operate the connected consumer, you can switch it on.
• Switch off the connected consumer (USB device), before you disconnect it from the USB port or before you
disconnect the charger from the car on-board power outlet.
• Pull the car on-board power plug out of the car on-board power outlet after use.
You can operate the charger with the engine running or stationary. However you should not start
the engine when the charger is connected, as the car on-board power outlet is interrupted during
the start (this must not necessarily apply to all vehicle models). If the engine is switched off,
drawing current over a longer period of time will discharge the vehicle battery.
If you determine, that the charger does not function normally (e.g. no charging, overheating),
there may be a short circuit. Immediately pull the car on-board power plug out of the car on-board
power outlet. Check with another car charger, whether the problem persists. Only plug the car
on-board power plug of the charger power adapter back into the car on-board power outlet after
it is ensured, that there is no longer a short circuit present. Check, whether the product functions
normally again. If the product does not function normally, pull it out of the car on-board power
outlet and dispose of it. In this case the product is defective.
Cleaning and care
• Each time before cleaning, disconnect the car on-board power plug from the car on-board power outlet and
any connected USB devices from the USB ports.
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical solutions
since these can penetrate the housing or impair functionality.
•
Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
Input voltage .....................................................9 – 32 V/DC
Output voltage ..................................................5 V/DC
Output power ....................................................
max. 9 A, 45 W
Output current per USB port .............................
max. 2.4 A
Total output current, dual-USB port ..................
max. 3 A (2 x USB port)
Total output current, four-fold USB port ............
max. 6 A (4 x USB port)
Cable length .....................................................
approx. 1.5 m
Operating/storage conditions ............................-10 to +40 °C, <90 % RH
Dimensions (W x H x D)
...................................
72 x 30 x 70 mm
Weight
.............................................................. 84 g
Operating instructions
CPAS-2400/6 USB car charger mains adapter
Item no. 1488842
Intended use
The product is suitable for charging and operating USB devices in vehicles. Power is supplied via an on-
board voltage socket. The dual-USB port on the plug is protected against overheating. The four-fold USB
port is protected against overheating and overloading and is short circuit proof. It is only allowed to be used
inside the car, in other words not outdoors. Avoid contact with moisture at all costs.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Mains charger
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions from our website www.conrad.com/downloads or scan the printed
QR code. Follow the instructions on the website.
Description of symbols
The symbol with a flash in a triangle indicates health risks e.g. due to electric shock.
The symbol with an exclamation mark in a triangle indicates important instructions contained in
these operating instructions that must be followed.
The "arrow" symbol alerts the user to the presence of important tips and notes on using the
device.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Always turn any connected appliance off before connecting or disconnecting it.
• Pull out the USB car charger when not in use.
•
The product gets hot during use. Ensure sufficient ventilation and never cover the product
during use.
• Do not short-circuit the USB outputs.
• Never use the product immediately after it has been brought from a cold room into a warm
one. The condensation generated could destroy the product. Allow the device to reach room
temperature before connecting and using it. This may take several hours.
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
*1488842_v1_0816_02_hk_m_en
