Intended use
This wireless light switch is intended for wirelessly turning on or off a light bulb that is screwed
into it, using a suitable radio remote switch.
The wireless light switch has a E27 light socket. Only screw in a light bulb with a maximum
output of 100 W.
The wireless light switch is only intended for use in dry indoor locations.
All the safety and operating instructions in this manual must be followed carefully. These in-
structions not only protect the device but, in particular, your health. Please read the entire
operating manual before using the product.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner.
All rights reserved.
Package Contents
• 1 x Wireless Light Switch
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty
will be void in such cases.
• The unauthorized opening, conversion and/or modification of this product is not
permitted because of safety and approval reasons (CE).
• The wireless light switch should only be used on a E27 socket with a voltage of
230 V/AC, 50 Hz.
• The product is not a toy and must be kept out of the reach of children. Therefore,
be especially careful when children are around. Children could try to insert items
into the openings of the device. There is a risk of a lethal electric shock!
• An all-pole disconnection from the mains voltage (such as a surge protector) must
be provided as part of the wiring set-up.
• The wireless light switch is only intended for use in dry indoor locations.
• Do not operate the product when it is covered. Ensure there is adequate ventilati-
on at the site of use.
• Never touch the light bulb you want to screw into the wireless light switch with your
hands, either during or after use (take note of the cooling time stated by the light
bulb manufacturer!). There is a risk of burns and of a fatal electrical shock!
• Do not overload the wireless light switch (take note of the input power in the tech-
nical data at the end of the operating manual!).
• Do not leave packing materials unattended. They may become dangerous
playthings for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• If the product’s casing is damaged, do not use the product anymore! In the event
that it is still connected to a source of electrical power, do not touch the product!
First shut down all poles of the current source (turn off automatic fuses/ fuses
and FI protective systems) and only after this unscrew the product from the lamp.
Take the product to a specialized repair shop or dispose of it in an environmentally
friendly way.
Programming the wireless light switch to recognise a radio
transmitter
• Set the switch group on the transmitter, to which you want to program the wireless light
switch, if necessary (e.g. for a radio remote control) using the selector switch for the switch
group.
• Screw the wireless light switch into an E27 socket. Make sure that the E27 socket’s connec-
ting cable is voltage-free.
• When the wireless light switch has been screwed into the E27 socket, the light bulb (E27,
max. 100 W) can then be screwed into the wireless light switch.
• Now, switch on the E27 socket (as usual, with the corresponding light switch), into which the
wireless light switch has been screwed. The red LED „Indicator“ starts to flash.
• Press the ON button for the desired switching channel on the radio transmitter, i.e. that to
which you want to program the wireless light switch, before the „Indicator“ LED stops blinking.
The red „Indicator“ LED is on. The programming has been completed successfully.
Programming a wireless light switch to recognise several radio
transmitters
You can program up to 10 radio transmitters for this wireless light switch.
• Set the switch group on the transmitter, to which you want to program the wireless light
switch, if necessary (e.g. for a radio remote control) using the selector switch for the switch
group.
• Screw the wireless light switch into an E27 socket. Make sure that the E27 socket’s connec-
ting cable is voltage-free.
• When the wireless light switch has been screwed into the E27 socket, the light bulb (E27,
max. 100 W) can then be screwed into the wireless light switch.
• Switch on the E27 socket (as usual, with the corresponding light switch), into which the
wireless light switch has been screwed.
• Press the „ON/OFF Learning Code“ button, until the „Indicator“ LED starts to flash.
• Press the ON button for the desired switching channel on the radio transmitter, i.e. that to
which you want to program the wireless light switch, before the „Indicator“ LED stops blinking.
The „Indicator“ LED is on. The programming has been completed successfully.
Deleting programmed wireless light switches from a radio
transmitter
Please observe the operating instructions for the corresponding radio transmitter.
Start-up, Function Test
Select the correct switch group on the transmitter, if necessary (e.g. on a radio remote control).
Switch on the E27 socket (as usual, with the corresponding light switch), into which the wireless
light switch has been screwed.
You can now test the wireless light switch’s functioning, by pressing briefly the ON button for
the corresponding switching channel. The red „Indicator“ LED lights up. The light bulb screwed
in lights.
Briefly press the OFF button, for the corresponding switching channel on the transmitter, the
LED „Indicator“ goes out. The light bulb screwed in lights.
The wireless light switch can also be switched on and off manually, by pressing the „ON/OFF
Learning Code“ button.
Maintenance and Care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Allow the product, and the light bulb that is screwed in to it, to cool down before cleaning.
Only clean the product when it is voltage-free!
Only clean the product with a soft, clean, dry cloth. Never use aggressive cleaning agents or
chemical solutions since these might damage the surface of the casing or impair the operation.
G
O P E R AT I N G I N S T R U C T I O N S www.conrad.com
Wireless Light Switch RSLR2
Item no. 640456
Version 03/15
