These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
V5_0713_02-HK
b) Miscellaneous
• In commercial facilities, the accident prevention regulations of the local association of workers’
compensation boards for electrical systems and equipment must be complied with..
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating elements
5
1 2 3
4
1 Thermostat
2 Indicator lamp
3 Multiple-contact switch
4 Fan grille
5 Handle
Operation
1. Place the unit on a heat-resistant, level surface. Make sure that the air entrance and exit are
unobstructed. The distance from the air intake grill to another object should be at least 20 cm. The
distance from the air outlet grill to another object should be at least 1 m.
2. Connect the unit to a properly installed wall outlet with 220-240 V/AC, 50 Hz .
- Cross section and fuse protection of the feed line on which you want to connect the unit should be
sufficient for its output.
3. Turn the unit on with the multiple-contact switch (3). The indicator lamp (2) lights up when the unit is in
operation.
- Switch position 0 – switched off
- Switch position fan operation only
- Switch position I – heat output 1000 W
- Switch position II – heat output 2000 W
4. Set the desired ambient temperature with the thermostat (1). When the set temperature is reached, the
unit switches off – or on again, if it goes below the set temperature.
5. Pull the plug out of the socket after use.
A slight odour of something burning after switching on should to a large extent vanish after a
short time, when all dust particles still on the heating wires have been burned.
Troubleshooting
Problem
Solution
The device doesn’t work.
Power connection interrupted / thermostat set too high / the
overheating protection has turned the unit off
• Check the power plug / set the thermostat / wait until the unit
cools off
The unit only blows cold air.
Heating not turned on / heating element defective
• Turn on heating level / repair by a specialist / specialised
workshop
The heating element gives off heat,
but the fan doesn’t work.
Fan motor defective
• Repair by a specialist / specialised workshop
Maintenance and cleaning
• Before every cleaning, separate the unit from the power network. If necessary, wait until it cools down to
normal temperature.
• Do not use any abrasive cleaners or solvents.
• It is best to clean the fan grille in front and back with a soft brush. If available, blow off the grille and internal
components with compressed air. But don’t use it in enclosed spaces or inhale the dust.
• The rest of the enclosure is to be wiped off with a soft dry cloth, as needed. If there is more dirt, please
use a lightly moistened cloth. After a longer period of not using the unit, make sure to remove most of the
dust deposits from the heating wires in the interior so that only slight remains are burned when turning it
on again.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ................... 220-240 V/AC, 50 Hz
Power consumption ................ 1800-2000 W
Dimensions (L x W x H) .......... 220 x 130 x 270 mm
Weight .................................... 925 g
Electrical fan heater, white
Version 07/13
Item no. 56 11 64
Intended use
The fan heater is for circulation or heating inside air. The integrated heating function can be optionally
switched on and has 2 levels of 1000 or 2000 watts. The unit may only be operated with 220-240 V/AC, 50 Hz
line voltage. The unit is Protection Class II compliant.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Fan heater
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Children should be supervised to ensure that they do
not play with the device.
• Cleaning and user maintenance shall not be made by
children without supervision.
a) Persons / Product
• Do not cover the device (e.g. with a curtain, blanket, etc.) to avoid overheating of the device.
When operating the heater, make sure there is sufficient distance from objects so as not to
interfere with air circulation. There is danger of fire!
• Never use the device without a protective grill. Do not put any objects through the safety guard.
• The heater must not be used near bathtubs, showers, swimming pools or washbasins. It must
not be possible to operate the heater when you are in contact with water.
• Do not position the device right underneath a mains outlet.
• Never touch the unit or the plug with damp or wet hands. This could result in a life-threatening
electric shock.
• Never touch bare wires (e.g., heating wires) with your bare hands.
• Never operate the device without supervision.
• The unit may only be used in dry inside areas.
• Never submerge the unit in water.
• In no case should you open the enclosure of the unit.
• Do not operate the device in conjunction with a timer, a separate remote control system or other
equipment which could turn the heating device on automatically. This would constitute a fire
hazard, as would covering the device or positioning it otherwise incorrectly.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• The device was constructed according to protection class II. Only a proper mains socket
(220-240 V/AC, 50 Hz) of the public supply net must be used as voltage source.
