Intended use
The power distribution socket allows you to connect a 12/24 V/DC load and it provides an ad-
ditional charging function for e.g. mobile phones, smart phones, tablets on so on, directly via
USB or micro USB.
The products
fi
ts into most of the drink or cup holders in vehicles and it thus can be securely
stored.
The power is supplied via the vehicle’s on-board socket with 12 or 24 V/DC.
Any use other than that described above is not permitted and can damage the product. In ad-
dition, it can lead to hazards such as short-circuit,
fi
re, etc.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package content
• Power distribution socket
• Operating instructions
Explanation of the symbols
In the operating manual, an exclamation mark inside a triangle indicates important
instructions.
The “hand” symbol indicates special information and advice on operating the device.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modi
fi
cation of the product is not permitted for
safety and approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children.
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
• Always disconnect the power supply of the loads to prevent unnecessary strain on
the vehicle battery.
• Make sure the maximum output current is not exceeded.
• Only use loads that are intended for the corresponding output voltage.
• During the installation always pay attention to a solid and secure hold.
• After the installation the control elements of the vehicle must be easily accessible.
• Be careful that no cables of the consumer affect vehicle operation.
Getting Started
Connect the distribution power socket to the vehicle’s on-board socket.
The power supply is indicated by a blue ring-light at each of the three connections.
Furthermore, a load/appliance with the vehicle plug can be used/operated via the 12/24 V/DC
socket integrated into the distribution power socket.
The two USB ports are used for standard USB cables.
The micro USB port is equipped with a connecting cable. Pull the latter out carefully until you
can feel the resistance. By pulling the cable brie
fl
y again, it winds up automatically.
If the distribution power socket still provides current after switching off the ignition
in your vehicle, it is advisable to disconnect the power supply to the vehicle if you
don’t need it any longer. Thus, the battery of your vehicle will not be strained un-
necessarily.
Replacing the fuse
1. Disconnect the power supply to the vehicle and if necessary, all consumer loads.
2. Carefully loosen the plastic nut right on the front of the plug by turning the nut counter-
clockwise and then remove the fuse.
3. Insert a new fuse of the same type and design. (see “Technical Data”).
4. Carefully close the plug on again.
5. The product is now ready for operation again.
Maintenance and Cleaning
The distribution power socket does not require maintenance.
The entire product can be cleaned easily with a moist cloth. To this end, use a soft cloth and
before starting the cleaning process, disconnect any connection to the vehicle and to the
respective loads.
Never use caustic cleaning agents or chemical solutions, as they could damage the surface of
the casing. Do not press too strongly to prevent damage to the product.
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical Data
Operating voltage ........................................ 12/24 V/DC via the vehicle’s on-board socket
Output vehicle socket .................................. 12/24 V/DC, max. 10 A
Output USB/micro USB ............................... 5 V, max. 2.5 A
Fuse .............................................................
fi
ne fuse 6.3 x 32 mm, 10 A
Length of connection cable .......................... approx. 100 cm (spiral cable)
Length of connection cable micro USB ....... ca. 58 cm
Dimensions .................................................. 76 x 70.5 mm (Ø x H)
Weight ......................................................... 140 g
O P E R A T I N G I N S T R U C T I O N S www.conrad.com
Distribution socket with 2 x
USB and micro USB
Item no. 55 44 04
Version 07/13
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
fi
lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.