CCD Board camera 8.47 mm (1/3”)
Version 04/12
Item no. 19 06 45
Sharp 420TV
Item no. 19 06 57
Sharp 540TV
Item no. 19 06 71
Sony 600TV
Item no. 19 06 86
AI 480TV
1. Intended use
The board camera with manual focus adjustment is designed for surveillance and security purposes in
uncontrolled and critical areas (such as shop, door intercoms, entrance areas or parking lots etc.). The
recorded images can be played back with sound on any suitable display device with video input (such as
TV or monitor).
The board camera is not permitted to use without protection (without the corresponding casing). It must be
power by 12 V/DC only. Contact with moisture must be avoided at all times.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2. Delivery content
• Board camera
• Cable with BNC & DC plug
• Operating instructions
3. Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
• Also observe the safety and operating instructions of any other devices which are connected to the
product.
• The board camera must be installed in proper housing in prior to operation.
• The board camera should not be installed in vicinity of strong magnetic or electric fields, e.g. mobile phones,
walkie-talkies, electric motors etc.
• The board camera is only permitted to be powered by power pack or a battery/accumulator with screened
and stabilized direct voltage. The voltage source must be able to supply sufficient power.
• After rapid temperature changes, the device needs approximately 15 minutes of stabilization to
accommodate to the new ambient temperature before use.
• When connecting the camera, make sure that the connection cables are not damaged by sharp edges.
• When using other devices or tools to assist the installation, the corresponding operating instructions must
be observed.
• When using a power pack as the voltage source, valid safety regulations must be followed under all
circumstances. Car chargers and toy transformers are not suitable as voltage sources and will lead to
damage to the components or to the device failing to function.
• When operating on commercial premises, the relevant accident prevention regulations of workers’
compensation boards for electrical equipment must be observed.
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4. Connection and operation
Use 12V/DC voltage source to power the board camera. Never try to operate the camera
with another voltage source. The DC source for the camera has to supply a current of 100
mA as minimum load capacity. Never overload the voltage source.
If you use a power pack as voltage source, this must be turned off during connecting.
Observe the polarity when connecting the voltage supply. If the polarity is not correct, the
components of the board camera may be destroyed.
Camera connections
Connect the small white plug of the connection cable with the camera module. This only fits into the socket
with the right polarity.
Video connection
Connect the video input of your TV or monitor with the yellow BNC socket of the camera module.
Use a suitable optional BNC connection cable (polarity: inside video, outside ground).
For any extensions, only use suitably shielded BNC cables. The use of other, unsuitable cables
may lead to interference.
Keep the length of the cable as short as possible.
Power supply connection
1. Connect the hollow power supply socket of the camera connection cable with a matching power pack.
2. The DC low voltage plug must have the following properties:
- Dimensions outside 5.5 mm, inner 2.1 mm.
- Polarity inside plus (+), outside minus (-).
Maintenance and cleaning
Apart from sporadically cleaning the lens, the board camera is maintenance-free.
Use a clean, lint-free, antistatic and dry cloth to clean the len. Do not use any abrasive or chemical agents or
detergents containing solvents.
5. Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
6. Technical data
Item no.:
19 06 45
19 06 57
19 06 71
19 06 86
Operating voltage:
12 V/DC
Current consumption:
60 mA
90 mA
60 mA
90 mA
Image sensor:
8.47 mm (1/3”)
Sharp Color CCD
8.47 mm (1/3”)
Sharp Color CCD
8.47 mm (1/3”)
Sony black & white
CCD
8.47 mm (1/3”) AI
black & white CCD
Light sensitivity:
0.8 Lux / F1.2
0.8 Lux / F1.2
0.02 Lux / F1.2
0.02 Lux / F1.2
Shutter speed:
1/50 (1/60) – 1/100,000 s
No. of pixels:
512 x 582 (PAL)
752 x 582 (PAL) 752 x 582 (CCIR) 537 x 597 (CCIR)
Horizontal resolution:
420 TVL
540 TVL
600 TVL
480 TVL
S/N ratio:
>48 dB
>48 dB
>48 dB
>48 dB
Video output:
≤ 1.2 Vp-p / 75 Ω
1.0 Vp-p / 75 Ω
≤ 1.2 Vp-p / 75 Ω ≤ 1.2 Vp-p / 75 Ω
Lens:
3.6 mm
Operation temperature:
-20 to +50 ºC
Cable length:
60 cm
Dimensions (W x H x D):
38 x 35 x 38 mm 38 x 35 x 38 mm 32 x 35 x 32 mm 38 x 35 x 38 mm
Weight:
50 g
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting,
also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
V1_0412_02-HL
