Connect Tech DAG103 User Manual Download Page 38 | Manualshive

Page: 38 / 47

background image

Xtreme I/O Express ADC-DAC

Users Guide

www.connecttech.com

Document: CTIM-00435
Revision: 0.08

Page 38 of 47

Connect Tech Inc. 800-426-8979 | 519-836-1291

Date: 2016-11-18

Flash Controller

Overview

The Mini PCIe ADC has a built-in flash controller to facilitate remote updates over the PCIe bus.
There are two usage modes – update flash and cold boot reconfig or update flash and live
reconfiguration.

Update flash and cold boot – the flash is erased and a new configuration image is written then
verified.  The FPGA is not update until the next power cycle.

Update flash and liver reconfiguration – the flash is erased and new configuration image is written
then verified.  The PCIe configuration registers are then save, the a configuration cycle is initiated,
and the PCIe configuration registers are restored.

Operation

For futher details on the flash controller operation, contact

[email protected]

to obtain the

necessary software package.

Memory Map

Offset

(Hex)

0x03

0x02

0x01

0x00

0x0000 SPI_CMD

0x0004 SPI_PARAM

0x0008 SPI_STATUS

0x000C SPI_RESULT

0x00100 SPI_PAGE_MEM

Register Details

For futher details on the flash controller operation, contact

[email protected]

to obtain the

necessary software package.

«
...
36
37
38
39
40
...
»

Summary of Contents for DAG103
















































Reviews:

No comments

Related manuals for DAG103

Brand: Ramsey Electronics Pages: 20

Brand: Vacon Pages: 6

iPort PT1000-CL

Brand: Pleora Technologies Pages: 29

Brand: Cable-Tronix Pages: 4

Brand: Samlexpower Pages: 56

Brand: BZB Gear Pages: 22

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: Mobotix Pages: 44

Brand: Peak Pages: 37

Brand: red lion Pages: 4

Brand: EverFocus Pages: 8

Brand: Satel Pages: 4

ETATRACK active

Brand: Lorentz Pages: 4

FC FC100PLUS Series

Brand: Janson Controls Pages: 94

Brand: Wen Pages: 28

Brand: IMC Networks Pages: 8

Brand: CYP Pages: 40

Cutter Inverter 25K

Brand: GYS Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands