12
QuickBridge Wiring Diagram Manual
QB4 BRIDGE RECEIVER WIRING
QB4 Bridge Receiver Wiring
250
QB4 RADIO WIRING
110VAC (or voltage needed for Mainline contactor on MAIN-OUT)
110VAC (or voltage needed for Mainline contactor on MAIN-OUT)
Output of MAIN-IN input voltage (if not needed, cap off)
Output of MAIN-IN input voltage (if not needed, cap off)
Signal input needed to run function
Signal input needed to run function
Output to Com1 (and Com2 if trolley present on hoist)
Output to Trolley East & West 2-speed function
Output to Down 2-speed function
Output to Up 2-speed function
Output to Trolley West 1-speed function
Output to Trolley East 1-speed function
Input from Aux 1 (if trolley present on hoist)
Output to Down 1-speed function
Output to Up 1-speed function
Input from Aux 1
Not used
Not used
Not used
Not used
Not used
(21) AUX 2S
(17) S/N 2S
(13) E/W 2S
(8) DOWN 1S
(7) UP 2S
K2 Hoist Receiver wiring
Not used
AC Neutral (or 12-24VDC -)
110VAC (or 12-24VDC+)
(4) MAIN-OUT
(3) MAIN-IN
(2) AC-2 (OR DC -)
(1) AC-1 (OR DC +)
(9) DOWN 2S
(12) WEST 1S
(11) EAST 1S
(10) COM 2
(6) UP 1S
(5) COM 1
(20) AUX 2
(19) AUX 1
(18) COM 4
(16) NORTH 1S
(15) SOUTH 1S
(14) COM 3
Not used
(21) AUX 2S
Output to North & South bridge 2-speed functions
(17) S/N 2S
Not used
(13) E/W 2S
Not used
(8) DOWN 1S
Not used
(7) UP 2S
K2 Bridge Receiver wiring
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
AC Neutral (or 12-24VDC -)
110VAC (or 12-24VDC+)
Not used
Output to North bridge 1-speed function
Output to South bridge 1-speed function
(4) MAIN-OUT
(3) MAIN-IN
(2) AC-2 (OR DC -)
(1) AC-1 (OR DC +)
(9) DOWN 2S
(12) WEST 1S
(11) EAST 1S
(10) COM 2
(6) UP 1S
(5) COM 1
(20) AUX 2
(19) AUX 1
(18) COM 4
(16) NORTH 1S
(15) SOUTH 1S
(14) COM 3
RELEASED
XA-574435
CAD SYSTEM: SOLIDWORKS
11/07/2016
D SAMPSON
K COCHRAN
11/07/2016
70051
ER APPR:
ER DATE:
ER ENGR:
ER NO.
STATUS:
11/07/2016
This drawing and the information shown constitute trade secret and confidential property
of Conductix, Inc. It is subject to recall, and is loaned for use only in connection with the
authorized manufacture or installation of Conductix, Inc. products, and on the condition
that it will be treated as confidential and will not be disclosed, published or reproduced in
whole or in part, or permitted to be viewed or used by any other party, without specific
written permission. Receipt and use of the drawing and information constitutes
acceptance and agreement to the above.
MINIMUM
MACHINED
SURFACE
0
10102 F Street
Omaha, NE 68127
800-521-4888
WEIGHT(REF): 0.00 LB
MAT'L: Material <not specified>
PROPRIETARY AND CONFIDENTIAL
UNLESS OTHERWISE SPECIFIED
INTERPRET GEOMETRIC TOLERANCING
PER: ASME Y14.5
PRIMARY UNITS ARE IN
INCH POUND SECONDS
SECONDARY UNITS IN
MILLIMETERS KILOGRAMS SECONDS
TOLERANCES ARE AS FOLLOWS
DECIMAL=
X.X 0.1 IN [2,5 MM]
X.XX 0.03 IN [0,8 MM]
X.XXX 0.010 [0,25 MM]
ANG. 1
FRAC. 1/16
THREAD CLASS: 2
ALL DIMENSIONS GREATER THAN 24.00 INCHES HAVE A
TOLERANCE OF .063 IN UNLESS OTHERWISE SPECIFIED
DRAWN:
APPR:
DESCRIPTION:
SIZE
B
MATERIAL NO. 2:
REV
SCALE:
1:4
K COCHRAN
D SAMPSON
SHEET
4
OF
6
RADIO SCHEMATICS FOR QUICK BRIDGE
