MESSAGE CODES
While operation, the following codes/symbols may appear on the display:
Message
code
Problem
Solution
203
Battery is too low.
Replace the batteries.
402
Calculation error.
Make measurement again.
301
Temperature is too
high.
Cool down the device to
operating temperature range.
302
Temperature is too
low.
Warm up the device to
operating temperature range.
101
Reflected signal is too
weak.
Choose the surface with
stronger reflectance. Use the
reflecting plate.
102
Reflected signal is too
strong.
Choose the surface with weaker
reflectance. Use the reflecting
plate.
201
Ambient light is too
strong.
Make measurements in less
illuminated zone.
401
Hardware error.
Switch on/off the device
several times. If the symbol
still appears, then the device
may be defective. Contact the
store where the device was
purchased, or an authorized
service center.
CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires careful
handling. The following recommendations will extend the life of the
device:
- Do not point the device at the sun.
- Protect the device from bumps, falls, and excessive vibration; do not let
liquids, construction dust and foreign objects get inside the device.
- Do not expose the device to extreme temperatures.
- If liquids get inside the device first remove the batteries, then contact
the service center.
- Do not store or use the device under high humidity conditions for a long
time.
- Clean the device with soft wet cloth.
- Keep device optics clean and protect it from mechanical damage.
- Сarry out control measurements occasionally, especially if the device is
subject to excessive mechanical or other impact, before and after taking
important measurements.
Failure to observe the following rules may lead to leakage of electrolyte
from the batteries and damage of the device:
- Remove the batteries from the device if it is not used for a long time.
- Do not use batteries of different types, with different charge level.
- Do not leave discharged batteries in the device.
UTILIZATION
Expired tools, accessories and package should be passed for waste recycle.
Please send the device to the following address for proper recycle:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Do not throw the device in municipal waste!
According to European directive 2002/96/ЕC expired measuring tools
and their components must be collected separately and submitted to
environmentally friendly recycle of wastes.
WARRANTY
All CONDTROL GmbH devices go through post-production control and are
governed by the following warranty terms. The buyer’s right to claim about
defects and general provisions of the current legislation do not expire.
1) CONDTROL GmbH agrees to eliminate all defects in the device, discovered
during the warranty period, that represent the defect in material or
workmanship in full volume and at its own expense.
2) The warranty period is 24 months and starts from the date of purchase by
the end customer (see the original supporting document).
3) The warranty doesn’t cover defects resulting from wear and tear or
improper use, malfunction of the device caused by failure to observe the
instructions of this user manual, untimely maintenance and service and
insufficient care, the use of non-original accessories and spare parts.
Modifications in design of the device relieve the seller from responsibility for
warranty works. The warranty does not cover cosmetic damage, that doesn’t
hinder normal operation of the device.
4) CONDTROL GmbH reserves the right to decide on replacement or repair
of the device.
5) Other claims not mentioned above, are not covered by the warranty.
6) After holding warranty works by CONDTROL GmbH warranty period is not
renewed or extended.
7) CONDTROL GmbH is not liable for loss of profit or inconvenience associated
with a defect of the device, the rental cost of alternative equipment for the
period of repair.
This warranty applies to German law except provision of the United Nations
Convention on contracts for the international sale of goods (CISG).
In warranty case please return the device to retail seller or send it with defect
description to the following address:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
