Condair Nortec GSTC Installation And Operation Manual Download Page 51

Page: 51 / 60

Links XPS Nortec GSTC/ SETC B+

Figure 31: Ethernet Port LED

Table 15: Links XPS Module Diagnostic LEDs

LED Name

Color

Function

Module Power

Off

Indicates that the Links module is not
receiving power.

Green

Indicates the Links module is operating
normally.

Receive LED (marked as Rx on
processor board)

Flashing Green

Indicates that the Links module is receiving a
network packet from a serial connection.

Transmit LED (marked as Tx on
processor board)

Flashing Green

Indicates that the Links module is transmitting
a network packet on a serial connection.

Ethernet LINK

Off

Indicates no Ethernet connection is present.

Solid Yellow

Indicates an Ethernet connection has been
detected.

Ethernet Activity

Off

No Ethernet network activity.

Flashing Green

Indicates Ethernet activity.

Summary of Contents for Nortec GSTC





























































Search results

Summary of Contents for Nortec GSTC

Reviews:

Related manuals for Nortec GSTC

Brands by name

Popular brands

Condair Nortec GSTC, Installation And Operation Manual

Search results

Summary of Contents for Nortec GSTC

Reviews:

Related manuals for Nortec GSTC

Brands by name

Popular brands