Concept2 VP4400, Manual

Page: 19 / 49

36 37
EN EN
VP4400 | VP4410 | VP4420 VP4400 | VP4410 | VP4420
OPERATING INSTRUCTIONS
ASSEMBLING THE VACUUM CLEANER
Warning
Always switch off the appliance and disconnect the charger from wall socket before assembling or removing accessories!
ACCESSORIES
The following accessories are included in the package for each type of appliance:
-
VP4400: 5, 6, 7, 8, 9 (see product description)
- VP4410: 5, 6, 7 (see product description)
- VP4420: 5, 6, 7, 8, 9 (see product description)
CHARGING THE BATTERY/LED INDICATOR
Make sure the vacuum cleaner is switched off before charging.
•
Place the vacuum cleaner into the charging stand.
• Plug the charger into the socket.
• The LED indicator light is red during charging.
• The LED indicator light is white when fully charged.
• The LED indicator light is white when using the vacuum cleaner.
•
If the battery capacity is low during vacuuming, the LED indicator flashes red. The vacuum cleaner switches off in
approx. 2-3 minutes.
• After the battery is discharged, the LED indicator goes off.
To prolong the battery life, follow these instructions:
•
Do not leave the vacuum cleaner completely discharged for a long time.
• Do not leave the vacuum cleaner permanently connected to the charger, even though it is fully charged.
• Do not let the vacuum cleaner to be completely discharged.
•
It is ideal to keep the capacity of the battery between 20-80 %.
USING THE VACUUM CLEANER
Before using the appliance, make sure that the vacuum cleaner filters are correctly positioned and that the dust container
is correctly seated.
1. Remove the vacuum cleaner from the charging stand.
2. Press the on/off switch to switch on the vacuum cleaner at low suction power.
3. Press the on/off switch second time to switch to high suction power.
4. Press the on/off switch third time to switch off the vacuum cleaner.
CHECKING THE FULLNESS OF DUST CONTAINER
If the suction power of the vacuum cleaner is reduced or the dust container is full, empty it and clean the vacuum cleaner
filter.
MAINTENANCE
It is recommended to empty the dust container and clean the vacuum cleaner filters after each use of the vacuum
cleaner.
EMPTYING THE DUST CONTAINER
1. Disconnect the charger from the mains.
2. Press the lock for emptying dirt on both sides, pull to separate it from the dust
container and empty the dirt.
3. After emptying the dirt, insert the lock back in the dust container. You will hear
a click when it is seated properly.
CLEANING AND REPLACING THE PERMANENT FILTER
The vacuum cleaner filter can be cleaned by mechanical tapping and cleaning with a
soft brush. Heavily soiled filter can be washed after this step and cleaned with a soft
brush in lukewarm water without detergents.
It is important to let the wet parts dry thoroughly. A wet filter would be depleted
by vacuuming!
Do not use a hair dryer for drying!
Note: Wet cleaning can cause more wear on the filter and thereby shortening its life.
•
The filter should be cleaned or replaced with visible soiling or when the suction
power of the vacuum cleaner drops. Check it after each use of the vacuum
cleaner.
• To avoid damaging the vacuum cleaner, do not use it without a properly fitted
filter and filter holder.
•
You can purchase a suitable filter type from your dealer or order from the
manufacturer.
CLEANING
Accessories and vacuum cleaner can be cleaned with a damp cloth.
Do not immerse the power cord or the charger in water or any other liquid.
Do not use aggressive substances such as solvents or abrasives for cleaning!
TROUBLESHOOTING
Problem Cause Remedy
The motor is not working The battery is discharged. Charge the battery.
Reduction of suction power
Full or clogged dust container. Empty and clean the dust container.
The filter is clogged. Clean or replace the filter.
Operating time at full charge is
less than 1 minute
The battery life is over.
Replace the battery with a new
one. Contact an authorized service
centre.