background image

Make sure the power cord is never crimped or damaged by sharp edges. If this occurs, 

replacement of the cable must be done by an authorized dealer. 

Always disconnect from the mains when the device is hot in use or before cleaning it. 

Only handle the power cord by the plug. Never pull out the plug by tugging the power 

cord. 

During initial start-up some smoke or smell may arise. This is a normal process and 

does not necessarily mean that the device is defective. It should decrease gradually. 

Please don’t project the beam onto combustible substances. 

Fixtures  cannot  be  installed  on  combustible  substances.  Keep  more  than  50cm 

distance  with  wall  for  smooth  air  flow.  Do  not  obstruct  fan  to  allow  maximum 

cooling. 

If  the  external  flexible  cable  or  cord  of  bar  is  damaged  it  should  be  replaced  by  the 

manufacturer  or  his  service  agent  or  a  similar  qualified  person  in  order  to  avoid  a 

hazard. 

 

4. Operation Instructions 

 

Don’t  turn on the fixture if it’s been through sever temperature difference like  after 

transportation  because  it  might  damage  the  light  due  to  the  environment  changes. 

Make sure to operate the fixture until it is in normal temperature. 

Avoid strong shaking during any transportation or movement. 

Don’t expose the fixture to overheating, moisture or environments with too much dust 

when  installing  it.  And  don’t  lay  any  power  cables  on  the  floor  or  it  might  cause 

electronic shock to the people 

Make  sure  the  installation  place  is  in  good  safety  condition  before  installing  the 

fixture 

Make sure to put the safety chain and check whether the screws are screwed properly 

when installing the fixture. 

Summary of Contents for V-PIX Vision Bar















Reviews: