Conairphone TAD1212 Owner'S Manual Download Page 13

13

PROBLEM

No answer

No power

No incoming
messages
recorded

POSSIBLE CAUSE

AC adaptor is disconnected
from wall outlet or back of
unit

AC adaptor is disconnected
from wall outlet or back of
unit

Unit is in the "OFF" mode

Power to electrical outlet
may be off

Power to electrical outlet
may be off

Telephone line is not
connected to wall jack

Telephone line is not
connected to wall jack

No audio on outgoing
greeting

CORRECTIVE ACTION

Reconnect AC adaptor into wall
outlet or back of unit.

Reconnect unit into wall outlet or back of
unit. Try connecting to a different wall outlet.

Check to see if electrical outlet is controlled
by a light switch and power is on, or wall
outlet may not be functioning, try connecting
to a different wall outlet.

Check to see if electrical outlet is controlled
by a light switch and power is on.

Reconnect AC adaptor into wall outlet or
back of unit. Try connecting to a different
wall outlet.

AC adaptor is disconnected
from wall outlet or back
of unit

Power to electrical outlet
may be off

Check to see if electrical outlet is controlled
by a light switch and power is on.

Check your outgoing greeting. If you do not
hear audio, record a new outgoing
announcement. See the section an

Recording Y our Outgoing Announcement .

Check to verify message counter is lit. Press
Answer ON/OFF control to turn unit on.

Connect telephone line into wall jack.
Telephone wall jack may not be functioning,
try connecting unit into a different telephone
wall jack.

Connect telephone line into wall jack. Try
connecting unit into a different telephone
wall jack.

Troubleshooting Guide (Cont.)

Summary of Contents for TAD1212

















Reviews: