manualshive.com logo in svg

Comrex BRIC-Link, Product Manual, Page: 90 / 95

Share
Download
Comrex BRIC-Link Product Manual Download Page 90

90

APPENDIX A - IP COMPATIBILITY

The BRIC-Link is capable of encoding and decoding a choice of three different types of non-BRIC-Link streams: 

Standard RTP

, 

Luci Live

 and 

Zephyr Xstream

. The choice is exclusive—i.e., you must set the BRIC-Link specifically 

for the type of stream you wish to be compatible with and you will remain incompatible with the other two types 
unless you change it. This setting has no effect on normal BRIC-Link functions, which continue to operate as before.

1. 

Luci Live

 - This PDA/PC-based software allows real-time streaming over IP links. As of version 1.2, 

Luci 

Live

 includes AAC and HE-AAC in addition to the default MP2 algorithm. BRIC-Link can communicate with

 

Luci Live

 only in Luci’s AAC modes. Note: The free demo available from Luci does not incorporate the AAC 

functions; you must have a licensed and registered copy to use AAC. 
To communicate with a 

Luci Live

 device: 

•  Initial Setup

 - This will define all Standard RTP connections to be Luci Compatible 

• 

BRIC-Link

 - On the 

System Settings 

tab, open the 

Standard RTP

 

Settings

 option and choose 

RTP 

Compatibility Mode

. On the pull-down box, choose 

Luci Live

.

• 

Incoming Connections

 - 

Luci Live

 sends either an AAC or HE-AAC stream to the BRIC-Link on UDP 

port 5004. These streams will be automatically decoded. By default, a return channel of AAC 56 kb/s 
mono is returned to the 

Luci Live

 product. The return channel may be altered to any Luci-compatible 

mode in the 

Systems Setting

 section.

• 

Outgoing Connections

 - Build a profile using the 

Profile Manager

 on the BRIC-Link and select a

 

Channel Mode

 of 

Standard RTP

. Then choose a Luci-compatible encoder for the outgoing call. The 

Luci software will control what type of stream, if any, is returned to the BRIC-Link.

2. 

Zephyr Xstream

 - Xstream Firmware version 3.2.0 and higher support an “RTP Push” function that is 

compatible with BRIC-Link in some modes. BRIC-Link is not currently compatible with the Xstream’s HTTP 
and SIP streaming functions.
There are several limitations imposed by the Xstream when using the RTP Push function:

•  On the Xstream, only AAC and MP3 coding are available in this mode, and BRIC-Link is only 

compatible with the AAC mode. 

•  The Xstream uses downsampling in modes below 96 kb/s, which is not supported by BRIC-Link. 
•  In order for an Xstream to decode an BRIC-Link

 

stream, the default decoder setting must be changed 

from <Auto> to <AAC> in the codec menu of the Xstream. 

To communicate with a 

Zephyr Xstream

:

• 

Initial Setup

 - This will define all Standard RTP connections to be Xstream Compatible. 

• 

BRIC-Link

 - On the 

System Settings 

tab, open the 

Standard RTP Settings

 option and choose 

RTP 

Compatibility Mode

. On the pull-down box, select 

Zephyr Xstream

. 

• 

Incoming Connections

 - 

Zephyr Xstream

 sends an AAC stream to the BRIC-Link on UDP port 9150. 

These streams will be automatically decoded. By default, a return channel of AAC 96 kb/s mono is 
returned to the Xstream. The return channel may be altered to any Xstream-compatible mode in the 

Systems Setting

 section. 

Summary of Contents for BRIC-Link
































































































Reviews:

No comments