manualshive.com logo in svg

COMPX RegulatoR, Instruction Manual, Page: 11 / 24

Share
Download
COMPX RegulatoR Instruction Manual Download Page 11

 

 

 RegulatoR

®

, Keyless Locking   11 

Changing the Supervisor Code 
To change the supervisor code, follow the steps on page 9 to enter programming 
mode. 
 
The factory default supervisor code is 12345 (supervisor codes must be 4 to 8 
digits in length.) 
 
There is a 10 second programming time limit between each step. If RegulatoR 
times out or an error is made, programming will end and you will need to enter 
programming mode again. 
 
 

1.

 

Place RegulatoR into programming mode (see page 9). 

2.

 

Press 2 and then press ENTER. 

3.

 

Type the current supervisor code and press ENTER. 

4.

 

Type the new supervisor code and press ENTER. 

5.

 

Retype the new supervisor code and press ENTER.  

6.

 

If successful, the green indicator light will illuminate for 1 second. 

 
Continue programming or press 9 and then ENTER to exit programming. 
 
RegulatoR

® 

features a reset code which will restore the default supervisor code 

and user code. RegulatoR was shipped with reset stickers; one attached to the 
back of the RegulatoR and an extra sticker that should be saved in a safe and 
secure location for future reference. 
 
To restore the factory default supervisor and user code, type the Reset Code 
assigned to the RegulatoR and press ENTER. 
 
CompX

®

 RegulatoR

®

 features several modes of operation. These functions can 

be changed using the following instructions with a valid supervisor code.   
 
 
 
 
 
 
 
 

Summary of Contents for RegulatoR

























Reviews:

No comments