background image

 

 

Interfaces and Connectors 

Revised May 2011 

SB-A510 Rev 1.1 

15

 

 

 

4.4 

USB Host Connectors (P11, P15) 

The four USB2.0 host ports provided by the CM-A510 are available through two dual type-A USB 
connectors (P11 & P15).  

For  USB  ports  1,  2  and  3,  the  CM-A510  provides  the  “VBUS  enable”  signal  and  monitors  the 
“VBUS  good”  signal  generated  on  SB-A510.    USB  port  0  power  is  controlled  by  GPIO00,  and 
monitored by GPIO01, on the I2C GPIO extender onboard the SB-A510. 

NOTE:  The  actual  number  of  USB2.0  ports  available  depends  on  the  CM-A510  USB 

configuration option. 

Table 11      P11 connector pinout (USB) 

USB port 0 (Bottom) 

USB port 1 (Middle) 

Pin 

Signal Name 

Pin 

Signal Name 

B1 

VCC_USB0 

B5 

VCC_USB1 

B2 

USBN0 

B6 

USBN1 

B3 

USBP0 

B7 

USBP1 

B4 

GND 

B8 

GND 

Table 12      P15 connector pinout (USB) 

USB port 2 (Bottom) 

USB port 1 (Middle) 

Pin 

Signal Name 

Pin 

Signal Name 

B1 

VCC_USB2 

B1 

VCC_USB3 

B2 

USBN2 

B2 

USBN3 

B3 

USBP2 

B3 

USBP3 

B4 

GND 

B4 

GND 

Table 13      P15/P11 connector data 

Manufacturer 

Mfg. P/N 

Mating connector  

YDS 

54F-10202GDD2 

Standard USB type A plug 

4.5 

Gigabit Ethernet Connectors (P11, P15) 

The SB-A510 is equipped with two Gigabit Ethernet RJ45 connectors (P11 & P15). P11 is interfaced 
with the CM-A510 LAN0 port, and P15 with the LAN1 port. 

Table 14      P11 connector pinout  (Ethernet) 

Pin 

Signal Name 

Pin 

Signal Name 

E1 

LAN0_CT1 

E10 

LAN0_CT2 

E2 

LAN0_MDIP0 

E11 

VCC3_3 

E3 

LAN0_MDIN0 

E12 

LAN0_ACT 

E4 

LAN0_MDIP1 

E13 

LAN0_LINK 

E5 

LAN0_MDIN1 

E14 

VCC3_3 

E6 

LAN0_MDIP2 

E15 

GND 

E7 

LAN0_MDIN2 

E16 

GND 

E8 

LAN0_MDIP3 

E17 

GND 

E9 

LAN0_MDIN3 

E18 

GND 

All manuals and user guides at all-guides.com

Summary of Contents for SB-A510
































Reviews: