background image

NAME: __________________________________

INV #: __________________________________

DATE: ___________________________________

BOX PULLED BY: __________________________

STAGED BY: ______________________________

SHIPPING WEIGHT: 850 lbs

PIECES: 20

MODEL PH35-10

_____1- 4’ x 4’ Deck package 

_____4- 9’ 6” Playhouse legs 

_____2 - Side Barriers 

_____1 - Entrance Barriers 

_____1 - Exit Barriers 

_____1- 8’ 4 rung ladder with adj. sleeves 

_____1- 10’ 4 rung ladder with

  adj. sleeves and 3rd leg sleeve 

_____1- 12’6” horizontal ladder 

_____1- 10’ 3rd leg 

_____1- 9’ x 2⅜” top rail 

_____1- 5’6” x 2⅜” top rail 

_____1- 10’ Plastic Rocket Slide _________

_____ 1 - Rocket Slide Foot 

_____ 2 - PH Canopy Arches 

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 

   

_____2- 5” swing seats __________________

_____1- trapeze bar ____________________

_____6- 2 ⅜” Brass Bushing Hangers

_____2- 3½’ chains ______________________

_____4- 7½’ chains ______________________

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

_____ 1 - Steering wheel _____________

_____ 1 - Steering wheel hardware pkg 

_____ 1 - Telescope _______________

_____ 1 - Telescope hardware pkg

_____ 1 - PH Canopy Tarp  ____________

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

_____ 1 - HL Bolt Pack

_____ 1 - 10’ Ladder Bolt Pack

_____ 1 - Playhouse bolt pack

_____ 1 - Spring Clip 12 Pack

_____ 8 - ⅜” x ⅜” set screws

_____ 4- 2 ⅜” plastic plugs

_____ 1 - Can of ____________ touch up paint

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

_____1 - Set of instructions

Last Modified: 6/1/2009

Summary of Contents for PH35-10
























Reviews: