background image

Note: To ensure your warranty is activated, complete and 
return this form within 10 days of installation. 

Return this form via e-mail to

:

[email protected]

O

r via U.S. mail to: 

Component Playgrounds 
1630 North Beck Street  
Salt Lake City, UT 84116 

Today’s Date:_____________________________________ 
Sales Receipt/Invoice Number:_________________________ 

Model(s):_____________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
______________________________________ 

 

CUSTOMER INFORMATION 

Project Name:_______________________________________ 
Contact Person:_____________________________________ 
Address:___________________________________________ 
City: ____________________State:______Zip:_________ 
Phone: ____________________

______

__________________ 

Purchase Date: __________Completion Date: ____________ 

SALES REPRESENTATIVE/DEALER INFORMATION 

(If different from manufacturer) 

Organization: _______________________________________ 
City: _____________________ State: ______ Zip: _________ 
Sales Rep Name: ____________________________________ 
Phone: _____________________

____

___________________ 

INSTALLATION INFORMATION 

(If different from customer or sales representative) 

Installed By: ________________________________________ 
Contact Person: _____________________________________ 
Address:  

City: _____________________ State: ______ Zip:_________ 
Phone: ___________

__________

_______________________

WARRANTY REGISTRATION SHEET

 

Summary of Contents for MT40-10

















Reviews: