Compex WP11A+ User Manual Download Page 98

Page: 98 / 101

Appendix III Configuration and Commands on Telnet Interface

Command

Examples

show tcp stat

show ethernet address

show gateway

set gateway <d.d.d.d

There are also some other commands such as:

set ip private <d.d.d.d> <d.d.d.d>
set ip lan <d.d.d.d> <d.d.d.d>
add ip routing <d.d.d.d> <d.d.d.d>
delete ip routing <d.d.d.d> <d.d.d.d>

AIII-3 How

recover Compex WP11A+ from failed firmware

This procedure details the upgrading of firmware to Compex WP11A+.

Compex WP11A+ will automatically switch to loader mode if the main code is
corrupted. Code can be corrupted due to power surges or it could be uploading
newer firmware results in router failing to startup.

1. Disconnect Compex WP11A+ from the network.

2. Connect one end of a MDIX cross-connect (MDIX) Ethernet cable on the WAN

port of Compex WP11A+ and the other end to your PC/notebook LAN adapter.

3. Power ON the device and the PC/notebook. You will notice that the DIAG LED

blinking rapidly. This indicates that the loader mode has discovered firmware
error and is awaiting uploading.

4. Insert the Product CD to your CD-ROM Drive.

Summary of Contents for WP11A+






































































































Search results

Summary of Contents for WP11A+

Reviews:

Compex WP11A+, User Manual, Page: 98 / 101

Search results

Summary of Contents for WP11A+

Reviews: