Compex WP11A+ User Manual Download Page 3

ii

FCC NOTICE 

This device has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This device generates, uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this device does cause 
harmful interference to radio or television reception, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Connect the computer into an outlet on a circuit different from that to which the receiver is 
connected. 

• 

Increase the separation between the computer and receiver. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

Caution:

 Exposure to Radio Frequency Radiation. 

To comply with the FCC RF exposure compliance requirements, the following antenna 
installation and device operating configurations must be satisfied: 
1.  For configurations using the integral antenna, the separation distance between the antenna(s) 

and any person’s body (including hands, wrists, feet and ankles) must be at least 2.5cm (1 
inch). 

2.  For configurations using an approved external antenna, the separation distance between the 

antenna and any person’s body (including hands, wrists, feet and ankles) must be at least 
20cm (8 inch). 
The transmitter shall not be collocated with other transmitters or antennas. 

Caution

: Any changes or modifications not expressly approved by the grantee of this device 

could void the user's authority to operate the equipment. 

FCC Compliance Statement:

 This device complies with Part 15 of the FCC Rules. Operation 

is subject to the following two conditions: 
1.  This device may not cause harmful interference, and 
2.  This device must accept any interference received, including interference that may cause 

undesired operation. 

Summary of Contents for WP11A+






































































































Reviews: