2
/
8
A10 Userinstruction (EN).docx
2019-07-10 R1 S5
Preface:
Thank you for choosing a Compac product.
Warranty:
A 1-year warranty is furnished with the product,
provided that the product is handled in accordance with the directions below.
Note: Do not undertake constructive changes.
Cautions
- safety measures
1.
The jack must only be used by trained personnel who have read and understood this manual.
2.
Avoid overloading. The capacity must not be exceeded.
3.
The jack must only be used on a horizontal, level and structurally stable substrate.
4.
The vehicle's wheels must be pointed forward, and braked or blocked.
5.
The jack is solely a lifting tool. Always support the vehicle with approved jack stands before working underneath the vehicle.
6.
Lift only at the vehicle's lifting points as prescribed by the manufacturer, and only centrally on the saddle.
7.
Being in, on or under a vehicle that is lifted or solely supported by a jack is forbidden.
8.
The jack may be used with a maximum of 1 standard extension piece delivered with the product.
9.
The jack - including the pressure relief valve - must not be modified.
10.
Maximum allowable air pressure: 10 bar/145 psi, minimum 300l/min.
11
. Min. distance to walls min. 0.5m wrt/ emergency escape routes.
12.
Lacking compliance with these warnings can cause the load to fall down or the jack to malfunction, which may result in
personal injuries or material damage.
The jack must only be used from -5° to + 40°
Mounting: See page 3
For mounting of joystick, see
picture (1-6).
IMPORTANT:
The hoses must go through the eye at the pull handle head, large hose at the bottom and small hose at the top
(see picture 4).
CAUTION:
Before placement into service and subsequently at periodic intervals, lubricate all movable parts with oil. Air connect
ion: 1/8”RG
(see picture 7). Full capacity is achieved from 8 bar. Maximum air pressure :10 bar/145 psi.
Operating manual:
Transport
Transport and store the jack standing on its wheels.
The handle
can be set in 3 different positions (see picture 8-10) by turning the handle counterclockwise and tilting it up or down
to the desired position.
Raising:
Press on the operating valve at the top of the handle (see picture 11), the pump will start and the jack will raise the
load.
Lowering:
Pull the handle up and turn it clockwise (see picture 12.13).
Maintenance:
Maintenance and repairs must be performed by qualified personnel.
As with all other pneumatic tools, the air motor requires oil for lubrication of moving parts. It is of special significance that, at
periodic intervals, the moveable parts around the lifting arm be lubricated, by lubricating via the 5 lubrication nipples (see points
on picture 20 and 21). It is recommended that an air supply be used with a filer/water trap and oil lubrication mechanism.
Monthly:
Empty the air supply's water trap and fill the lubrication mechanism up with oil. Lubricate all movable parts with oil.
Remember lubrication via the 5 nipples in lifting arm (picture 20 and 21). At the same time, check jacks and extension pieces for
damage and abnormal wear. For obvious wear of moving parts, replace them at an authorized workshop with original spare
parts.
Annually:
Replace filter (see picture 14,17,18)
Check the safety valve by pulling in the eye or air to whistle out of the valve 2-3 times (see picture19)
Oil filling:
Fill up with oil (see picture 14-16). The correct oil level is 10 mm below the top edge of the hole, when the jack is
standing horizontally and the lifting arm is completely down.
Oil quantity:
A1,6+A2 = 0.4 l; A4 =1.0l; A10 = 1.2l.
Oil type:
Hydraulic oil with viscosity ISO VG 15, for example Castrol Hyspin AWS 15, Mobil DTE 10 Excel 15 or the equivalent.
Never use brake fluid!
Safety inspection:
