background image

Page 9 of 9

© 2021 CommScope, Inc. All Rights Reserved

10 

Trademarks and patents 

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. This 

document is for planning purposes only and is not intended to modify or supplement any specifications or warranties 

relating to CommScope products or services. CommScope is committed to the highest standards of business integrity 

and environmental sustainability, with a number of CommScope’s facilities across the globe certified in accordance with 

international standards, including ISO 9001, TL 9000, and ISO 14001.

Further information regarding CommScope’s commitment can be found at

www.commscope.com/About-Us/Corporate-Responsibility-and-Sustainability.

This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com.

11 

Contact information

Visit our website or contact your local CommScope representative for more information.

For technical assistance, customer service, or to report any missing/damaged parts, visit us at:

http://www.commscope.com/SupportCenter

Summary of Contents for TC-1511-IP










Reviews: