background image

7

Trade-marks

All trademarks identified by 

®

 are registered trademarks in the US and may be registered in other countries. All third

party product names, trademarks and registered trademarks are property of their respective owners.
This document is for planning purposes only and is not intended to modify or supplement any specifications or

warranties relating to CommScope products or services. CommScope is committed to the highest standards of business

integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in

accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.
Further information regarding CommScope’s commitment can be found at: https://www.commscope.com/corporate-

responsibility-and-sustainability.
This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com

8

Contact information

Visit our website or contact your local CommScope representative for more information.
For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://

www.commscope.com/SupportCenter

page 9 / 9

© 2021 CommScope, Inc. All Rights Reserved

Summary of Contents for NOVUX










Reviews: