CommScope 3603D-1U-144LC-LS-A Instructions Manual Download Page 15 | Manualshive

Page: 15 / 15

background image

www.commscope.com

860479229

Issue 7, May 2013

Page 15 of 15

Step 10 – Building Up and Stacking Trays

Note

: Do NOT remove paper backing from adhesive on bottom of additional trays.

1. Align 4 holes on base (provided for plastic hardware) with 4 holes on elevated platforms of previous tray.

Additional trays must be rotated 180

°

from the previous tray orientation.

2.  Install snap rivet grommets and plungers.
3.  Install top cover.
4.  Repeat as required.

Note:

Three trays may be used in a 1U shelf for a total of 144 fusion splices. Six trays may be used in a 2U shelf

for a total of 288 fusion splices and twelve trays may be used in a 4U shelf for a total of 576 fusion splices.

Top cover

3-tray stack

Snap rivet
plunger

Snap rivet
grommet

«
...
13
14
15

Summary of Contents for 3603D-1U-144LC-LS-A
















Reviews:

No comments

Related manuals for 3603D-1U-144LC-LS-A

Brand: BAS-IP Pages: 18

Brand: Eclipse Pages: 48

Brand: Eclipse Pages: 52

Brand: Eclipse Pages: 48

Brand: Eclipse Pages: 5

Brand: Eclipse Pages: 21

WIZARD ELEGANCE IP

Brand: Fasttel Pages: 14

Brand: SanRex Pages: 4

Brand: LaserLine Pages: 68

Brand: CAME BPT Pages: 8

Brand: R-Tech Pages: 20

Brand: Opus Technologies Pages: 24

Smart Home Monitoring

Brand: Rogers Pages: 5

Brand: Leister Pages: 14

Brand: MPS Pages: 4

kb sound Series

Brand: EIS Pages: 2

Brand: Mark Climate Pages: 60

Brand: US Shift Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands