background image

10

HINTS WHEN USING THE PUMP

The maximum pumping rate only occurs when using the largest hose or tube diameter possible, if

smaller diameter hoses or tubes are used, the rate will reduce relative to the size of the

hose/tube. Try to use discharge pipes which have a larger diameter than the discharge outlet.

Running the pump with no water flowing through leads to increased wear and is not recommended.

The pump must be immediately unplugged as soon as water stops flowing through.

The pump will automatically switch off in the event of overheating due to the built-in thermal

overload protector. After cooling down, the motor automatically switches on again.

When disconnecting the pump from the mains power supply, do not pull by the power cable (9).

Using 3 fingers around the 3 pin power plug, gently pull and disconnect from the mains power. 

MAINTENANCE

Under normal conditions, the pump does not require any maintenance.
Make sure the pump is disconnected from electric power supply before performing 

maintenance procedures.

Cleaning the Pump Housing

Use a moist cloth to wipe down the pump housing (2). Allow to dry thoroughly before storing in a dry

location that is protected from bad weather conditions.

Cleaning the Suction Base & Filter

Remove the filter from the base of the pump and gently hose down the base and filter separately with

low pressure water. Allow to dry thoroughly before storing. When required replacement filters can be

purchased from the Special Orders desk at your local Bunning's store.

Power Cable

For all submersible pumps, a H07RN-F cable is required to be fitted. Contact Commercial Electric
customer service for replacement cable.

SPARE PARTS

Limited spare parts are available subject to availability. Please contact your local Bunnings Special

Orders Desk to order the required spare parts.

Most common spare parts listed below
Spare Part 

Part No.

Filter 

SPPBC350-28

Outlet pipe lower section

SPPBC350-34 

Outlet pipe upper section

SPPBC350-35 

Tap connector

SPPBC350-36 

Rubber seals (Pack 2)

SPPBC350-38 

Cord restraint

SPPBC350-39 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for PBC-350
















Reviews: