Commercial Electric C423100 Use And Care Manual Download Page 3

 

3 HOMEDEPOT.com

 

 

Please contact 1-877-527-0313 for further assistance.

Warranty

THREE (3) YEAR WARRANTY
WHAT IS COVERED

The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three 
(3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products 
used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your 
exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the 
product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This 
warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not 
in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product 
as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating 
to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as 
surface and/or weathering, as this is considered normal wear and tear.

WHAT IS NOT COVERED

The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, of fitness 
for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability 
and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/
expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Pre-Installation

PLANNING INSTALLATION

Read all instructions before installing. 
To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.

NOTE:

 Personal injury and damage to the LED strip and/or mounting surface 

may result if the LED strip is pulled from the surface. To reduce the likelihood 
of injury or damage, mount only on a surface that is structurally sound.

TOOLS REQUIRED (NOT INCLUDED)

Phillips  
screwdriver

Pencil

Brush

Measuring  
tape

HARDWARE INCLUDED

NOTE:

 Hardware not shown to actual size.

AA

BB

Part

Description

Quantity

AA

Screw

16

BB

Clip (type MH1)

2

Summary of Contents for C423100













Reviews: