7
REMOTE START FEATURES
Lock (+)
From Door Switch
Unlock (+)
From Door Switch
5 Wire "Ground at rest" Door Lock System
3 Wire Positive Door Lock System
X
5 WIRE
FACTORY
SWITCH
ACTUATOR
DOOR LOCK WIRING DIAGRAM
Or use the optional DL-INV or D-DLS
4
Bypassing Factory theft Deterrent Systems:
Most factory deterrent systems are now using either a resistor coded key or a
passive transponder that allows the fuel system to function properly only
when the coded key is inserted into ignition. Therefore when starting the
vehicle remotely without the key, the vehicle's theft deterrent system will only
allow the vehicle to start if it "reads" the proper coded key or transponder in
the ignition. If you try and start the vehicle with any of these systems and do
not bypass it then the vehicle will crank but the fuel system will shut down
and not run.
REMOTE START FUNCTIONS:
1.- Press button #2, Siren will chirp3 times parking lights will turn on solid,
LED will begin to flash rapidly to verify that the vehicle is about to start
remotely.
Ignition relays #1 & #2 will provide 12V+ output first (Yellow & Brown wires),
the Red wire on the 3 pin accessory harness will pulse to turn off the factory
alarm. (If applicable)
After 3 seconds the start relay will then provide 12 V+ for approximately 1
second (violet wire) or until it senses that the car has started.
Immediately after the car has started the accessory relay will provide 12V+
output (Orange wire). Air conditioning or heater should now turn on. Engine
will run for 12 minutes.
2.- Press button #1 to unlock vehicle (if the keyless functions are used), and
enter vehicle. Do not hit brake pedal before turning the ignition on or the
vehicle will shut down.
3.- Insert the ignition key and turn to ignition position only!!!.
If the key is
turned all the way to the crank position, the starter will over grind and
possibly damage the starter.
Once the ignition is turned on, the vehicle may
be operated normally. If the vehicle needs to be remotely shut down during
the run cycle, press button #2 on the transmitter Siren will chirp 6 times and
the vehicle's engine will stop running.
Valet Mode:
To get into Valet mode, turn the Ignition ON, hold the push button switch for 5
seconds until the LED comes ON solid. The system will be in VALET. Only the
door lock/unlock system will work on Valet (Keyless Entry).
To get out of Valet mode, turn the ignition ON and hold the switch down for 5
seconds,
Longer Crank Times:
Some vehicles require a longer cranking time, to achieve this you must turn
the dip switch #2 to an off position.
Diesel Mode:
Vehicles with a diesel engine can be remote started by placing the dip switch
#3 to an OFF position. By doing this your ignition will be turned on for 20
seconds before starting the vehicle, allowing a time for your glow plugs to
warm up.
Factory
Door Lock Switch
3 Wire Negative Door Lock System
Existing Power
door lock system
Alarm Door Unlock Wire
Alarm Door Lock Wire
12V Power (+)
Not Needed
87
85
86
8 7 a
30
87
8 7 a
30
85
86
Alarm Door Unlock Wire
Alarm Door Lock Wire
DOOR LOCK
ACTUATOR
Aftermarket Power door lock Actuator
12V Power (+)
Ground
87
85
86
8 7 a
30
87
8 7 a
30
85
86
Alarm Door Unlock Wire
Alarm Door Lock Wire
12V Power (+)
87
85
86
8 7 a
30
87
8 7 a
30
85
86
Alarm Door Unlock Wire
Alarm Door Lock Wire
X
Stop-N-Go Feature:
If you wish to exit the car and remove the ignition key but keep the car running.
1-
While Ignition is on Position Press the brake pedal and hold.
2-
While pressing the brake pedal press button # 1 on the transmitter for 2seconds.
3-
The LED should now be flashing rapidly.
4-
While In STOP-N-GO Mode The Parking Lights Will Flash 5 Times.
5-
Release the brake pedal and turn the ignition switch to OFF position, Remove key.
Now you may exit the vehicle and lock the doors with the keyless entry feature.
When reentering the vehicle simply turn ignition key to ON position (Do not start),
Press the brake pedal and the STOP & GO feature will be OFF.
Cold Start Feature:
1-
Press And Hold Brack Pedal
2-
Press And Hold Valet Switch
3-
Press Button #2 for 3 seconds, Parking Lights will flash five (5) times. Then Engine
starts for 30 seconds, to acknowledge the setting. Once programmed the engine will
start every 2 hours or one houre as program for 15 or 25 minutes, for total of 12 times
only.
To Turn The Cold Start Feature OFF:
1 -
REPEAT STEP ONE. LIGHTS WILL FLASHES 10 TIMES.
2 -
DEACTIVATE BY STEPPING ON THE BRAKE.
3 -
WHEN THE USER STARTS THE CAR WITH REMOTE CONTROL.
4 -
DEACTIVATE BY TURNING ON THE IGNITION.
ALL THE ABOVE WILL CANCEL THE COLD START MODE.
