Comfort Zone CZ2032C Owner'S Manual Download Page 2

2

WARNING:  READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.

Thank you for choosing a Comfort Zone® Infrared Heater. This owner’s manual will provide you with 

valuable information necessary for the proper care and maintenance of your new product. Please take a few 

moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your 

new heater. 

IMPORTANT INSTRUCTIONS

When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, 

electric shock, and injury to persons, including the following:

1. 

Read ALL instructions before using this unit.

2. 

CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.

3. 

This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If 

provided, use handles when moving this heater. 

4. 

Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 

3 ft. from the front of the heater and keep them away from the sides, top and rear. DO NOT place 

towels or other objects on the heater. 

5. 

Extreme caution is necessary when any heater is used by or near children or the disabled, or any 

time the heater is operating.

6. 

Do not operate this heater unattended or while sleeping.

7. 

DO NOT operate any heater with a damaged cord or in case the heater malfunctions, has been 

dropped or damaged in any manner. Return heater to authorized service facility for examination, 

electrical or mechanical adjustment, or repair.

8. 

This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. 

NEVER locate heater where it may fall into a bathtub or other water container. To protect against 

electrical hazards, DO NOT immerse in water or other liquids. 

9. 

DO NOT touch the control panel or plug with a wet hand. 

10. 

DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar 

coverings. Arrange cord away from traffic area and where it will not be tripped over.

11. 

DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may 

cause an electric shock or fire, or damage the heater.

12. 

To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on 

soft surfaces, like a bed, where openings may become blocked. 

13. 

A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, 

explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and 

open flames.

14. 

Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or 

relocatable power tap (outlet/power strip). 

15. 

To avoid fire or shock hazard, plug the unit directly into a 120V AC electrical outlet. 

 

Summary of Contents for CZ2032C











Reviews: