Comfort Glow and CVDR30 Owner'S Operation And Installation Manual Download Page 10

www.fmiproducts.com

901265-U

10

Installation and Gas Connection

1.  Place burner pan assembly in center of 

fireplace  floor.  Make  sure  front  of  pan 
faces forward.

2.  Thread gas supply fitting to fireplace gas 

supply pipe. Use thread sealant.

3.  Install adapter fitting onto burner inlet fit

-

ting using thread sealant on male threads 
of burner inlet fitting (see Figure 7). Adjust 
to most convenient position.

4.  Install gas connector tube to gas supply 

fitting. Carefully shape tube to attach to 
adapter  fitting.  Be  careful  not  to  cause 
kinks in tube.

INSTALLATION

Continued

Figure 7 - Connecting Gas to Appliance

Adapter 

Fitting

Gas 

Connector 

Tube

Burner Pan 

Assembly 

(Facing Front 
of Fireplace)

OPTIONAL GA9050A-1 ON/OFF SAFETY 
VALVE/PILOT KIT ASSEMBLY

For additional convenience and safety, or for 
propane/LP conversion, an optional ON/OFF 
safety valve/pilot kit is available. See 

Acces-

sories

, page 26.

 WARNING: You must use a 

ON/OFF safety valve/pilot kit for 

propane/LP conversion.

Natural Gas Installation

1.  Thread gas control valve onto burner inlet 

fitting (see Figure 8). Use thread sealant 
on male threads of burner inlet fitting. Hold 
burner inlet fitting with a wrench to prevent 
overtightening connection to the burner. 
Make sure control rod is facing the front 
(see Figure 8).

2.  Attach pilot gas line to pilot outlet of gas 

control valve and tighten. Connect ther

-

mocouple  to  rear  of  gas  control  valve. 
See Figure 9. Do not overtighten. If us

-

ing propane/LP gas, see 

Changing Pilot 

Orifice

, page 12.

3.  Install inlet fitting into inlet opening of gas 

control valve (see Figure 10). Use thread 
sealant on male pipe threads.

4.  Place burner pan assembly in center of 

fireplace  floor.  Make  sure  front  of  pan 
faces forward.

5.  Thread gas supply fitting to fireplace gas 

supply  pipe. Adjust  to  most  convenient 
position.

Burner Inlet 
Fitting

Gas Control 
Valve

Burner Pan 

Assembly

Figure 8 - Installing Gas Control Valve

Control Rod

Figure 9 - Gas Control Valve with 

Thermocouple and Pilot

Figure 10 - Installing Inlet Fitting and 

Gas Connector Tube

Thermocouple 

and Line

Pilot and 
Line

Gas Control 
Valve

Gas Control 
Valve

Gas Inlet 
Fitting

Gas 

Connector 

Tube

Inlet 

Opening

Summary of Contents for and CVDR30





























Reviews: