Comfort Bilt HP22, Operator'S Manual

Page: 5 / 34

Operator’s Manual
HP22 Pellet Stove
~ 5 ~
CAUTION
ALL APPLICABLE BUILDING CODES FOR YOUR
LO
CATION MUST BE FOLLOWED. IN AREAS WHERE
BUILDING CODES REQUIRE ADDITIONAL STEPS TO THE
INSTALLATION OF THIS PRODUCT NOT INCLUDED IN THIS
MANUAL, THE BUILDING CODES WILL TAKE PRECEDENT
AND MUST BE FOLLOWED. CONTACT YOUR LOCAL
BUILDING INSPECTOR TO OBTAIN ANY NECESSARY
PERMITS OR INSPECTION GUIDELINES BEFORE
INSTALLING THE PRODUCT.
• Contact local building or fire officials about
restric
tions and installation inspection requirements in
your area.
•
Contact your local authority (such as municipal building
department, fire department, fire prevention bureau, etc.) to
determine the need for a permit.
• This pellet stove is designed to
burn pellet fuel
only.
• A working smoke detector is required and
must be installed in the same room as the stove.
• This stove is not intended for use in
commercial
applications.
• Door and ash pan must be closed and
latched during
operation.
• Notify your insurance company of pellet stove
instal
lation.
• This installation must conform with local
codes. In
the absence of local codes you must comply
with EN 14785.
• The structural integrity of the
manufactured home floor, wall, and ceiling/roof
must be maintained.
• Keep combustible materials (such as
grass, leaves,
etc.) at least three feet away from the
flue outlet on the outside of the building.
• This stove should not be used as the only
source of heat in the house. Power outages and
periodic maintenance will result in a total loss of
heat.
• Do not leave hopper door open while unattended.
CAUTION
INSTALLATION AND REPAIR OF THIS PELLET
STOVE
SHOULD BE DONE BY A QUALIFIED SERVICE
PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ONCE A YEAR BY A QUALIFIED
SERVICE PERSON. IT IS IMPERATIVE THAT THE CONTROL
COM- PARTMENTS, FIRE BOX, AND THE CIRCULATING AIR
PASSAGEWAYS OF THE STOVE BE KEPT CLEAN.
THE OPERATION OF EXHAUST FANS SUCH AS
BATH-
ROOM FANS, ATTIC FANS, ETC. MIGHT STARVE THE
PELLET STOVE OF COMBUSTIBLE AIR CREATING A
NEGATIVE PRESSURE IN THE ROOM. PROVIDE ADE- QUATE
VENTILATION OF THE ROOM ACCOMPANYING
THE PELLET STOVE. IF NOT, THE PRESSURE
SWITCH
MAY SHUT OFF OPERATION OF THE PELLET
STOVE.
THE MOVING PARTS OF THIS STOVE ARE
PROPELLED BY
HIGH TORQUE ELECTRIC MOTORS.
THESE PARTS CAN CAUSE SEVERE DAMAGE TO BODY
PARTS THAT GET NEAR THEM. KEEP ALL BODY PARTS
AWAY FROM AU- GER AND FANS WHILE THE STOVE IS
PLUGGED INTO AN
ELECTRICAL OUTLET. THESE MOVING PARTS
MAY BE-
GIN TO MOVE AT ANY TIME THE STOVE IS
PLUGGED IN.
THE VENT SURFACES CAN GET HOT ENOUGH
TO CAUSE
BURNS IF TOUCHED. NONCOMBUSTIBLE
SHIELDING OR GUARDS MAY BE REQUIRED.
INSTALL VENT AT CLEARANCES SPECIFIED BY
THE
VENT MANUFACTURER.
ALL VENTING JOINTS, WHETHER VERTICAL OR
HORI-
ZONTAL, SHOULD BE MADE GAS-TIGHT WITH REC-
OMMENDED SEALANTS SPECIFIED BY VENT MANU-
FACTURER.
ACCORDING TO HUD (HOUSING & URBAN
DEVEL
OPMENT) REQUIREMENTS, WHEN INSTALLED IN A
MOBILE HOME, THIS STOVE MUST BE GROUNDED
DIRECTLY TO THE STEEL CHASSIS OF THE MOBILE
HOME AND BOLTED TO THE FLOOR. DIRECT
AIR ACCESS MUST BE PROVIDED, USE A
FRESH AIR KIT.
FOR USE IN THE UNITED STATES AND CANADA.
AP-
PROVED FOR INSTALLATION IN MOBILE
HOMES.
PRODUCER OF THIS APPLI
ANCE, RESERVES THE
RIGHT TO ALTER ITS PRODUCTS, SPECIFICATIONS AND/OR
PRICE WITHOUT NOTICE.