GWD 910 / 915
Wireless Microphone System Owner’s Manual
9
Operating Procedure
The GWD915/910 is designed to eliminate unnecessary hassle of pairing a receiver with a
particular wireless microphone. With the latest technologies, the GWD915/910 is able to
synchronize the frequency of any GWD915T/910T Wireless Microphone with any
GWD915R/910R Receiver.
Just follow these few simple instructions to ensure maximum performance:
1.
Check out any GWD910T Wireless Microphone and make sure it is fully charged
before operation.
2.
Please be sure the IN-CAR VIDEO SYSTEM is ON before proceeds any further.
3.
Slide the wireless microphone
contact directly on top of the
receiver’s register contact (
located on
the top of the IN-CAR VIDEO
SYSTEM monitor module
) until a
confirmation tone has sound. This
indicates the receiver’s register
contact has synchronized the
frequency of the receiver and the
wireless microphone. Wireless
microphone is now on standby mode
and is ready for use.
4.
Please only synchronize one wireless microphone to one receiver.
5.
There are three methods to activate recording on the wireless microphone:
a.
Press the ON or Panic Button once on the wireless microphone for
recording.
b.
Activate video recording at the IN-CAR VIDEO SYSTEM. This action
will automatically trigger wireless microphone recording.
c.
Turn on the light bar or siren in the patrol car. This action will also
automatically trigger wireless microphone and video recording.
6.
To prevent accidental audio shut off. The only way to return wireless
microphone to standby mode from recording mode is to stop the video recording
from the IN-CAR VIDEO SYSTEM.
Or press and hold PB2 until 3Seconds
.
7.
During recording mode, if the warning sounds and the yellow LED flash, this
means the signal is marginal or weak. At this time, please step closer to the
receiver or reposition the wireless microphone until the warning stops. However,
if the warning persists and exceeds 30 seconds, the wireless microphone will
automatically shut off and return to standby mode. If user returns within the
signal range again while the video is still recording, the receiver will re-initiate the
wireless microphone automatically.
8.
For charging, simply place the wireless microphone to the charger and leave it
charging for at lease 6 (six) to maximize battery capacity.
GWD 910 / 915
Wireless Microphone System Owner’s Manual
10
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment. .
FCC RF Radiation Exposure Statement:
To comply with the FCC RF exposure compliance requirements, this device and its
antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
For next to mouth operation, this device has been tested and meets FCC RF exposure
guidelines when used with an accessory that contains no metal and that positions the
device a minimum of 10 mm from the face. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines
For limb-worn operation, this device has been tested and meets FCC RF exposure
guidelines when used with an accessory that contains no metal and that positions the
device a minimum of 0 mm from the body. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines
