background image

 
 

 

 

 

12

 

 

IE-COM-D0221-05

 

 

 

Reading ALLO indicates adjusted lower alarm limit. Set the desired 
value by means of the arrow keys. Press and hold the arrow key UP 
to make value increase fast. Press and hold the arrow key DOWN to 
make value decrease fast. Release the arrow key and press ENTER 
to confirm new limit.  
 
 
Reading ALHI indicates adjusted upper limit. Set the desired value in 
the same way as in above lower limit. If needed it is possible to get 
back to lower  limit setting of the same alarm by pressing DISPLAY 
key. Press ENTER key to confirm new upper limit. 
  
 
 
Then  you  are  offered  to  set  alarm  of  other  input  value  (here 
temperature of channel 2). The procedure is the same as the above 
temperature  limit  setting.  Alarm  activation  of  each  value  can  be 
disabled  by  setting  lower  alarm  limit  of  the  desired  value  up  to  its 
maximum. This is indicated by OFF reading at the position of numeric 
value. Value of upper limit of the same alarm is indifferent. 
 
It is possible to leave the alarm setting mode by pressing MENU key. 
New adjusted limits up to pressing MENU key are stored in memory.  
 
After  pressing  ENTER  key  it  is  possible  to  set  alarm  limits  for 
temperature difference between channels.  

 

Summary of Contents for Commeter D0221





















Reviews: