ComAp InteliDrive DCU Marine Manual Download

Page: 119 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

119

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

[DISABLED, ENABLED]

Default value

DISABLED

Step

[-]

Comm object

11327

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

The setpoint enables/disables logging of remote communication activity. If logging is enabled connection

and disconnection of each remote terminal as well as entering access code are recorded into the history.

Note:

The terminal is disconnected automatically after 5 min of inactivity and next communication

request from the same terminal is considered as a new connection. When logging is enabled in certain

conditions the history may be filled up with large number of records related to the communication and

important records may be overwritten quite fast.

LB/UART Log

back to List of setpoints

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

[9600, 19200, 38400, 57600, 115200] [bps]

Default value

9600

Step

[-]

Comm object

24477

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

The setpoint adjusts communication speed of the RS232 interface when

RS232 Mode (page 120)

is set to

MODBUS.

RS232 MBCSpd

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands