7
P/N: 83874-Sub1
Rev AE February 2018
(ENGLISH)
ENGLISH
CHAIN CONTAINER INSTALLATION
IMPORTANT!
Read all instructions before attempting to install chain container to hoist.
Please see detail images at the end of this document for more information. Caution should be used to ensure chain does not tangle if
manually loaded into container before operation. If chain becomes tangled and contacts the bottom of the hoist, damage may occur.
The recommended method of feeding chain into the container is by operating the hoist in the up direction, allowing chain to feed into the
container.
1. Installing the chain container:
a. Temporarily route loose-end of load chain over chain container bracket, as shown in Point B of Figure 1.
b. Place one large flat washer (2) on one 75mm bolt (1), followed by a retainer wire (3) loop and another large washer. Feed the bolt
through a reinforced hole in chain container from the outside.
c. Once through the reinforced hole in the container, add another large washer (2), followed by one spacer (4).
d. Insert the bolt through one hole in the mounting bracket. Add one small flat washer (5) to the bolt. Add one nylon-insert lock nut (6)
onto bolt. Tighten the nut by hand to the extent it will not fall off. See Figure 2 for details for steps 1b-1d.
e. Loop the retainer wire (3) around the suspension (10) until the loose end is near the remaining bracket mount. See Figure 3.
Note:
multiple loops around the suspension may be necessary to remove unnecessary length from the retainer wire.
f. Repeat steps 1b-1d for remaining side.
g. Torque lock nuts (6) to approximately 4.5 lb·ft (6.1 N·m).
h. Route loose-end of load chain into chain container as shown in Point C of Figure 1.
i. The chain container is now ready for operation.
Note:
Loose-end screw (12) should be torqued to approximately 4.5 ft·lbs (6.1 N·m).
A
B
C
FIGURE 1
Chain routing during and after assembly. Point A is hook-end of load chain. Point
B is temporary routing of loose-end of load chain before bag assembly. Point C
is final routing of loose-end of load chain after bag assembly.
Item No.
Part Number
Description
Qty.
1
192040587
BOLT, HEX-HEAD, M10X1.5MMX75MM, Z/P
2
2
192040588
WASHER, FLAT, M10-10.5MMIDX30MMOD, Z/P
6
3
24651
RETAINER WIRE
1
4
192040536
SPACER, WINDMILL CHAIN BAG
2
5
192040589
WASHER, FLAT, M10-10.5MMIDX20MMOD
2
6
192040590
LOCKNUT, NYLON-INSERT, M10X1.5MM Z/P
2
FIGURE 2
Hardware configuration for attaching chain container to bracket.
FIGURE 3
Typical configuration of chain container
to hoist. Note: retainer wire (3) may need
to be wrapped around suspension (10)
multiple times.
FIGURE 4
Exploded view showing assembly
of chain container to bracket.
Summary of Contents for CM LODESTAR
