Colortronic CTT 1200 Operating Instructions Manual Download Page 58

Page: 58 / 96

5.6. Changing the battery of the control system

This work may be carried through only by qualified personnel trained in the
field of electrical engineering.

The battery may be changed only with the control system switched on.

Open the control box by means of the control box key which is part of the supply.

Open the front door of the CPU.

Pull the backup battery with cable out of the compartment.

Plug the connector of the new backup battery into the corresponding socket in the battery compartment of
the CPU.

The notch on the

battery connector must point to the left!

Place the backup battery into the battery compartment on the CPU

Close the front door of the CPU

Close the control box.

64.10-8255GB01

05/03

CTT 1200

Maintenance 5-12

Summary of Contents for CTT 1200

































































































Search results

Summary of Contents for CTT 1200

Reviews:

Related manuals for CTT 1200

Brands by name

Popular brands

Colortronic CTT 1200, Operating Instructions Manual

Search results

Summary of Contents for CTT 1200

Reviews:

Related manuals for CTT 1200

Brands by name

Popular brands