background image

 

28

 

Appendix A - Rules, Regulations and Safety Concerns 

 

 

FCC rules require that during operation of this type of equipment a minimum separation of 20 cm 
(8 inches) must be maintained between the antenna and persons.  This regulation should be 
adhered to whenever the camera may be powered on, either in its final installation or during 
configuration and testing. 
 
FCC rules require that the camera be operated only with the supplied antenna.  Do not attempt to 
operate the unit with any other antenna type.  Do not touch the antenna during operation. 
 
Pacemaker manufactures recommend that a minimum separation of 20 cm (8 inches) be 
maintained between the camera and a pacemaker. 
 
Enfora certifies that the Enfora Enabler II-G 

TM 

 MHz GSM radio Module (FCC ID: 

MIVGSM0108) complies with the RF hazard requirements applicable to broadband PCS 
equipment operating under the authority of 47 CFR Part 24, Subpart E of the FCC Rules and 
Regulations.  This certification is contingent upon installation, operation and use of the Enfora 
Enabler II-G and its host product in accordance with all instructions provided to both the OEM 
and end user.  When installed and operated in a manner consistent with the instructions provided, 
the Enfora Enabler II-G meets the maximum permissible exposure (MPE) limits for general 
population / uncontrolled exposure as defined in Section 1.13.10 of the FCC Rules and 
Regulations. 
 
Equipment intended or use in a residential environment (not-withstanding use in commercial, 
industrial or business environments) is designated as Class B.  The Enfora Enabler II-G module 
has been tested and found to comply with the limits for a Class B digital device and can be 
integrated into equipment or applications intended for use in residential environments. 
 
Do not use the camera when wireless phone use is prohibited or where it may cause interference.  
These areas typically include; hospital, aircraft, in explosive atmospheres, in areas where blasting 
is in progress. 
 
The camera can be damaged when subjected to large shocks.  Do not drop the camera. 
 
Abrasive cleaners or strong solvents will damage the acrylic windows.  Wipe with a damp cloth 
only. 
 
When properly assembled the camera enclosure is weatherproof.  It will withstand assault by 
normal levels of wind and rain.  It may not survive extreme weather conditions.  It is not built to 
withstand water from high-pressure sources or submersion. 
 
Use only the dealer-supplied AC adapter when powering the camera externally. 
 
Contact the dealer for details on powering the camera by other external means (lead-acid 
batteries, solar panels ,etc). 
 
The camera has minimal protection against reverse hookup to external electrical connections; it 
may be damaged by such a connection. 
 

Summary of Contents for Observer IV


















































Reviews: