background image

160-167

R 100%

G75%

B100%

168-175

R 100%

G 100%

B 100%

176-183

R 100%

G 100%

B 25%

184-191

R 100%

G 100%

B 50%

192-199

R 100%

G 100%

B 75%

200-207

R 100%

G 100%

B 100%

208-215

R 20%

G 100%

B 100%

216-223

R 40%

G 100%

B 100%

224-231

R 60%

G 100%

B 100%

232-239

R 80%

G 100%

B 100%

240-247

R 20%

G 100%

B 100%

248-255

R 50%

G 50%

B 50%

8.

8.

8.

8. Technical

Technical

Technical

Technical Specifications

Specifications

Specifications

Specifications

Input Voltage: AC 90-260V/50-60HZ

LED Quantities: 16 red/ 16 green/ 16 blue (3W)

Control Signal: DMX512

Control Channel: 8CH

Power Consumption: 144W

Gross Weight: 9kg

Shipping Dimension: 530*230*200mm

9.

9.

9.

9. Key

Key

Key

Key Features

Features

Features

Features

48*3W red, green and blue LEDs

Colors optional for customers, single color or RGB

LED RGB technology with 256 degree gray scale function

Synchronous effect through intelligent controller

DMX controller controllable

8 DMX channels

Digital IP address together with built-in fixed program for synchronization and self-link

Light angle and position adjustable for optimal lighting effect

Applicable for both indoor and outdoor like stage, bar, nightclub,

courtyard, architectural, theme park, etc. (Protection rating: IP 56)

2.

2.

2.

2. S

S

S

Safety

afety

afety

afety IIIInstructions

nstructions

nstructions

nstructions

 

 

This device has left the factory in perfect condition. In order to maintain this condition

and to ensure a safe operation, it is absolutely necessary for the user to follow the

safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes due to environmental

changes, do not switch it on immediately. The arising condensation could damage

the device. Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this

manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.

During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall

be exclusively replaced by the manufacturer or his service agent or a similar qualified

person in order to avoid a hazard.

Summary of Contents for W-010







Reviews: