background image

LED

LED

LED

LED Zoom

Zoom

Zoom

Zoom Par

Par

Par

Par

SI-0

SI-0

SI-0

SI-051

51

51

51

User

User

User

User Manual

Manual

Manual

Manual

KEEP

KEEP

KEEP

KEEP THIS

THIS

THIS

THIS MANUAL

MANUAL

MANUAL

MANUAL FOR

FOR

FOR

FOR FUTURE

FUTURE

FUTURE

FUTURE NEEDS

NEEDS

NEEDS

NEEDS

1

1

1

12

2

2

2.... Maintenance

Maintenance

Maintenance

Maintenance and

and

and

and Cleaning

Cleaning

Cleaning

Cleaning

The following points have to be considered during the inspection:

1) All screws for installing the devices or parts of the device have to be tightly connected and must not be

corroded.

2) There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling,

suspension, trussing).

3

Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.

4

The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage have to be adhered by a skilled installer

and any safety problems have to be removed.

 

 

 

In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the

lights.

1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation

of dust.

2) Clean the fan each week.

3) A detailed electric check by approved electrical engineer each three month, make sure that the circuit

contacts are in good condition,

prevent the poor contact of circuit from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or

solvents.

There are no serviceable parts inside the device. Please refer to the instructions under “Installation

instructions”.

Should you need any spare parts, please order genuine parts from your local dealer.

Summary of Contents for SI-051







Reviews: